News Gigabyte/ASUS/GALAX RTX 4060 Low Profile

Michitaro · Mar 31, 2024

Edit: I see you are doing custom fans. 2x80mm should work fine if they hold pressure and you can make a shroud so all the air goes through the fins. I think Noctua makes a 60mm fan? NF-A6x25

Problem with 80mm fans is that they are also blowing air underneath the card (they are much taller than the radiator) I think that's the reason for insufficient air pressure. One fan also extends beyond the radiator (card is not as long as 2x80mm fans combined), but it shouldn't be as negative for the air pressure? I think I am best off with getting those 60mm

SFFMunkee · Apr 1, 2024

milesvw said:
Why not just use a PWM adapter to control the stock fans with the motherboard?

https://www.amazon.com/Cerrxian-Speed-Supports-Ethernet-Laptops/dp/B07S4L41TN

Edit: I see you are doing custom fans. 2x80mm should work fine if they hold pressure and you can make a shroud so all the air goes through the fins. I think Noctua makes a 60mm fan? NF-A6x25

I’m actually considering doing this for mine so I can up the power limit and still have full speed fans.

Michitaro · Apr 10, 2024

To utilize the increased power limit of new bios, I got myself PTM7950 thermal solution + 3x A6x25. While indeed they work better than 2x A8x25, my case has no clearance, and the fans had to be attached by a single screw to the side panel of my A24-V5. I believe because of that the fans are "vibrating" a lot, when put at 60% or more speed. Overall when running at 80-100% the card stays relatively cooler, but the noise and "sound" of it is just unbearable.

What would you recommend in my case? Trying to push some pads between fans and side panel, which will bend the card in pcie slot? Going with some slim 60mm fan (20/15/10 mm). I don't own a 3d printer, nor capabilities to make a custom shroud for such fans. Or maybe just keep card as it is, and run it with 90% PL + UV so temperatures never hit 90 degrees @3500 RPM

Jay85 · Apr 15, 2024

SFFMunkee said:
Scratch that, I've managed to successfully crossflash the quiet VBIOS and overclocked VBIOS from another Gigabyte card.

It's hard to tell how well it works as the RTX4060 power measurement is fairly bogus at best, but with the +13% set in Afterburner HWInfo shows 130W usage at full tilt compared to 115W with the stock LP VBIOS.

But - GREAT NEWS --> FAN STOP / Zero RPM Fan mode WORKS !!

I've also managed a slightly higher TimeSpy Graphics score at 11,705 when paired with the same hardware as before.

Necro'ing this thread because of the post, what did you use in the end to get the bios flashed onto the 4060 LP?

Looking to do the same to increase the power limit and use the fan stop function. Did you just flash the Overclocked VBIOS to get the fan stop working or do both bios's work?

Thanks

Jay85 · Apr 15, 2024

Successfully flashed the bioss on the 4060 LP, the extra 13% PL overhead is really good! Got a similiar score to SFFMunkee in time spy.

Stock Run:

Overclocked: +125 +1300mem

Bios Flashed: Same settings as SFFMunkee but Mem @1500

SFFMunkee · Apr 15, 2024

Jay85 said:
Successfully flashed the bioss on the 4060 LP, the extra 13% PL overhead is really good! Got a similiar score to SFFMunkee in time spy.

Stock Run:

Overclocked: +125 +1300mem

Bios Flashed: Same settings as SFFMunkee but Mem @1500

Nice work!! I need to go get a fan adapter so I can keep my 0 rpm fan, full speed fan AND higher PL...

Jay85 · Apr 16, 2024

SFFMunkee said:
Nice work!! I need to go get a fan adapter so I can keep my 0 rpm fan, full speed fan AND higher PL...

I will need to do the same, if you find a good adapter to use let me know please

.

Gotta admit, even though i've done vbios flashes on older gpu's, it was still abit nerve racking on a 4000 series card since i've never done it on this card or used the new software before with the bypass. The instructions in the github were nice and clear though.

Snerual · Apr 18, 2024

Chiphell has more info on the Asus card it seems.

The website is in Chinese but the pictures also reveal interesting info. I still fail to understand why they made such a long LP card. Barely any cases it fits in.

Snerual · Apr 19, 2024

.... and now Galax has a model as well

Looks quite spiffy with the all-white design but again 182mm long so... impossible to fit in many cases.

Gingerbeer · Apr 19, 2024

182mm long with the power socket right at the end of the board, with no recessing. What a shame, because it looks great.

Analogue Blacksheep · Apr 19, 2024

Gingerbeer said:
182mm long with the power socket right at the end of the board, with no recessing. What a shame, because it looks great.

While low profile custom cables do exist, like this one on Moddiy, putting the connector at the front does seem a bit silly considering the use case in SFF builds.

Jay85 · Apr 19, 2024

Snerual said:
.... and now Galax has a model as well

Looks quite spiffy with the all-white design but again 182mm long so... impossible to fit in many cases.

I think its an instant buy for me, white and low profile. Might need to make a custom SFF case just for this.

hrh_ginsterbusch · Apr 19, 2024

Jay85 said:
I think its an instant buy for me, white and low profile. Might need to make a custom SFF case just for this.

No need, the Ophion 7L in white would be almost perfect for this

cu, w0lf.

ondert · Apr 20, 2024

hrh_ginsterbusch said:
No need, the Ophion 7L in white would be almost perfect for this

cu, w0lf.

Nah 7L is too big. My last A2000/HDPlex GaN 250w case was 4.5 liters.

milesvw · Apr 22, 2024

ondert said:
Nah 7L is too big. My last A2000/HDPlex GaN 250w case was 4.5 liters.

Try 2.5L

. PIO JW H610 motherboard from Taobao less than 100 shipped, including superbuy battery removal service. I'm expecting my second one any day. Used Alienware GaN PSU. (Yes room for it inside if desired.)

ondert · Apr 22, 2024

milesvw said:
Try 2.5L . PIO JW H610 motherboard from Taobao less than 100 shipped, including superbuy battery removal service. I'm expecting my second one any day. Used Alienware GaN PSU. (Yes room for it inside if desired.)

Sounds like a system will work sensibly good

what’s the case?

Jay85 · Apr 22, 2024

So i reached out to my Bykski contact to see if they had any plans on making a block for the Gigabyte 4060 LP, currently no plans but will keep me informed if things change.

Jay85 · Apr 23, 2024

Old news but the 4060ti single slot is out in the wild. It's loud... maybe SFF guys can do a mod on it, if it becomes available for the rest of the world.

Galax's single-slot RTX 4060 Ti is out in the wild, though sadly it appears to be a little tempestuous | PC Gamer

milesvw · Apr 24, 2024

ondert said:
Sounds like a system will work sensibly good what’s the case?

Log - Revocases TIPIO1 build with GTX 4060 and 12th gen

This Log will detail fitting a 4060 Low Profile and a JW H610i-PIO motherboard in a Revocses TIPIO1 "1.9L" case (Well, I currently have 8mm standoffs under the lid, so add some CM²). Currently rocking an i5 12500t and 2x16GB 3200Mt/s DDR4. Shouldn't be much of a bottleneck at 1440p, and the...

smallformfactor.net

This with 8mm standoffs on the lid screws and a little bracket for the GPU corner. Left the second slot Display port covered by the case.

Completed - REVOCCASES RCC-TIPIO1 | 1.9L Thin ITX PIO Console Case

TIPIO1 is a just-for-fun concept for Thin ITX PIO boards and low profile single slot GPUs Specs: Volume: ca. 1.9L Motherboard: Thin Mini ITX PIO 17x17, e.g. JUBO H310C-G GPU: Low Profile Single Slot, up to GTX1650 PSU: small 19V GAN Adapter CPU cooler: ultra low profile

smallformfactor.net

(There is a different "revoccase" that may work with mods: https://smallformfactor.net/forum/t...x-case-optional-1-56l-thunderbolt-egpu.17105/)

Analogue Blacksheep · Apr 26, 2024

ASUS 4060 LP build in a Captain Case V8

News Gigabyte/ASUS/GALAX RTX 4060 Low Profile

Minimal Tinkerer

Buy first, justify later?

Minimal Tinkerer

Chassis Packer

Chassis Packer

Buy first, justify later?

Chassis Packer

Cable-Tie Ninja

Cable-Tie Ninja

SFF Lingo Aficionado

King of Cable Management

Chassis Packer

King of Cable Management

Airflow Optimizer

SFF Lingo Aficionado

Airflow Optimizer

Chassis Packer

Chassis Packer

SFF Lingo Aficionado

King of Cable Management

Similar threads