I used a 15cm cable for the 24pin, but it's a very tight fit. 20vm would be still tight, but more manageable
Chimera Industries Cerberus: The 18L, mATX, USA-made enclosure
- Thread starter PlayfulPhoenix
- Start date
Hey All,
Got my build underway! Turns out the ATX PSU that I had will not fit with my res mounted to the front rad/fan combo... so I ordered an SFX-L PSU last night... Hopefully be able to get this guy booted up next week...
Modifying the Heatkiller tube wasn't too bad. Took a bit of time and fortunately have a friend that has a ton of tools that was willing to help me out.
More details are embedded in each picture below.
Got my build underway! Turns out the ATX PSU that I had will not fit with my res mounted to the front rad/fan combo... so I ordered an SFX-L PSU last night... Hopefully be able to get this guy booted up next week...
Modifying the Heatkiller tube wasn't too bad. Took a bit of time and fortunately have a friend that has a ton of tools that was willing to help me out.
More details are embedded in each picture below.
Thanks! First water build, first SFF build. Lots of scraped fingers and cursing.
Galletabah is correct.
So I've got the hydrocopper installed and hooked into the bottom part of the loop. Question -- can I have the out line going through the opposite side of the inlet into the CPU block or is that what they mean by not connecting them on the same side due to severe performance penalties?
EDIT: nevermind, there's a nice chart in the install media (RTFM...) that shows it'd be a bad idea.
Also, I bought an in-line temp probe thinking that my motherboard had an input for the two pin connector, turns out it doesnt. Any elegant way of attaching it to my system?
EDIT: nevermind, there's a nice chart in the install media (RTFM...) that shows it'd be a bad idea.
Also, I bought an in-line temp probe thinking that my motherboard had an input for the two pin connector, turns out it doesnt. Any elegant way of attaching it to my system?
@carpenike I think I might have been the one who sold you the Hydrocopper on /r/hardwareswap lol. I hope it came out of shipping alright
@carpenike I think I might have been the one who sold you the Hydrocopper on /r/hardwareswap lol. I hope it came out of shipping alright
Haha! Small world! Yup its all good. Thanks again! Got it installed today.
@carpenike I suggest you to open a dedicated topic on your build log. I'm sure it will pretty be interesting.
i have aquaero 5lt in my case. Ill show you my setup in a few hours.
I want to say that I order scythe fuma rev B(dual a12x25) to compare with c14S
complete setup:
aquaero 5 LT in the bottom, left corner:
All cables are custom. I dont know if will use noctua fans or nidecs fans for cpu cooler because I already have 2 ap15 but fan(3 pin) speed spikes a lot with the aquaero
aquaero 5 LT in the bottom, left corner:
All cables are custom. I dont know if will use noctua fans or nidecs fans for cpu cooler because I already have 2 ap15 but fan(3 pin) speed spikes a lot with the aquaero
Optimum Tech with another Cerberus build. A Threadripper 2950X this time:
Easy assembly and cooling.
Enermax Liqtech (if now reliable) seems to be a really good cooler..
Heh, so the SFX PSU arrived, but it doesn't have an ATX adapter, so now I need the SFX rear mount for the Cerberus. Another couple day delay.
Ahah i could have tell you that..Heh, so the SFX PSU arrived, but it doesn't have an ATX adapter, so now I need the SFX rear mount for the Cerberus. Another couple day delay.
Boy, that's an expensive build if the whole loop is comprised of fittings. How many fittings are there?
Similar threads
