-
Save 15% on ALL SFF Network merch, until Dec 31st! Use code SFF2024 at checkout. Click here!
Stalled [New Video Assembly] Densium 4 & 4+ - Tiny cases with real hardwood frontpanel!
- Thread starter Densium.net
- Start date
Same here. Are cases being shipped based on order numbers Audun ?One of the original backers. Still waiting.
Ditto, waiting for a D4+ and Z39 cooler package in transfer message. Got another order with the tiny antenna and gpu risers in the mail about a week ago though. Guessing its just a matter of timeOne of the original backers. Still waiting.
Best way to integrate a SATA SSD in that formfactor would be like @sergiiua from Custom_Mod did with his FX Cases:
You can do a vertically mounted SATA SSD screwed in with two holes at the bottom of the case, right infront of the PSU.
(it would therefore need to have just enought spacing for that solution of ~7mm clearance between case pannel and PSU shroud)
I know M.2 is the best solution for space and performance, but thanks to SilverStone CP10 Slim-SATA cables (SST-CP10) its not bad for SFF.
Maybe a option for the V2 that would open up more storage options and get the additional 7-8mm with the PSU pushed into the CPU side
for extra height for the CPU cooler? That would add up perfectly for 47mm cooler options.
The Densium 4 is right now 220x98x190 = ~4,1L volume
With the additional 8mm in width you would be looking at 220x106x190 = ~4,43L volume and getting just with a small increase
both bigger CPU coolers and SATA SSD mounting option!
Now add maybe the option for 92x14mm Fan to the top for additional exhaust (maybe a integration of max. of two 92mm fans at the top and the mounting holes would be integrated in the airholes pattern and would blend just in with the design so if no fans are mounted it would be still minimalistic and clean.
The case would be then 234x106x190 = ~4,71L...maybe call it the Densium 47 the Agent under the SFF cases!
Obviously it would be needed to test if the additional exahust through the top would benefit the temps to be worth adding the additional height.
Last edited:
Good news and bad news!
The good news is that I received both my cooler and chassis today!
bad news is they are both damaged a bit.
the finish is ruined on both and the cooler fins are bent which isn't a huge deal tbh. the upsetting part is the powder coating on the chassis. its on both the top and bottom
The good news is that I received both my cooler and chassis today!
bad news is they are both damaged a bit.
the finish is ruined on both and the cooler fins are bent which isn't a huge deal tbh. the upsetting part is the powder coating on the chassis. its on both the top and bottom
Just got a shipping alert. 
I'm excited and slightly concerned. Fingers crossed all is well.
Will give an update when is reaches me in Ireland.
I'm excited and slightly concerned. Fingers crossed all is well.
Will give an update when is reaches me in Ireland.
upon further inspection, it's actually rusting under the Powdercoat. I have fully disassembled the chassis and looks like the only part with issues is the outside frame. the sides and the motherboard tray are all fine
I got a response from my support email. Both the frame and cooler will be replaced and I am very grateful for it. Hopefully I was just a unlucky one and every one else has good cases.
Audun is a top man. Always there to help.
Does anyone know where I could buy a good PCIe Gen4 x16 bifurcation cable ? Considering the Densium 4, but I would want to run a single-slot LP RX 6400 video card & ConnectX-3 10Gb NIC. I would want PCIe 4.0 for the RX 6400. Sliger sells a Gen3 with their cases & shows what I would want in the below link for the Gen4 bifurcation cable:
Hoping everyone gets their orders sorted out. This case is fun to build in!
Managed to squeeze in a 5800X3D and a secret GPU into a Densium 4. Check out the build log HERE!
Managed to squeeze in a 5800X3D and a secret GPU into a Densium 4. Check out the build log HERE!
Hoping everyone gets their orders sorted out. This case is fun to build in!
Managed to squeeze in a 5800X3D and a secret GPU into a Densium 4. Check out the build log HERE!
Well done sir.
Well done.
If i'm not mistaking Densium sells a gen 4 riser that fits the case in their shop. I got one, yet to trmest it though.
My case arrived today.
Good news: it arrived safe and sound. Looks great, and even my wife likes it.
Bad news: wrong size.
Good news: it arrived safe and sound. Looks great, and even my wife likes it.
Bad news: wrong size.
Similar threads
