Thoughts, yes... plans, no.
Spoilsport ? - but I can't argue with your reasoning ?
Completed Lone Industries L5 - 4.6L Mini ITX
- Thread starter Lone
- Start date
Spoilsport ? - but I can't argue with your reasoning ?
Welcome to the forum!
Depending on what your future power requirements are, you could possibly go with a slim Dell 130/150W external AC adapter, which would still be quite portable. Just an idea. This is the simplest, fully supported option.
I'm not sure whether the HDPLEX 200W AC-DC is a good option or not. It will technically fit at the front (without the front fans and fan mount), but the HDPLEX 200W DC-ATX would also have to be relocated to the front (next to the 200W AC-DC) using a short 24pin extension cable. You would also have to figure out where to mount the AC power jack, or use a pigtail connector run outside the case.
If you do plan to try to stuff an HDPLEX 200W AC-DC in there, you may want to consider going with the Noctua NH-L12S cooler, and/or put an 80 mm case fan at the bottom (when vertical) mounting location in the case.
EDIT: Another potential fitment issue with the HDPLEX 200W AC-DC is that any GPU cards longer than the motherboard will not fit, unless you shift the HDPLEX 200W AC-DC towards the top/right of the case, and put the DC-ATX in front of the GPU card.
Last edited:
The HDPLEX 200W DC-ATX features back mounting holes on the heatsink spaced at 48 mm, which will mount directly to the vent holes at the front of the L5 (July batch with 3.2 mm vent holes). This is untested though, and it might look nicer just using double sided adhesive, than have visible screws on the front of the case.
Last edited:
Preparing for another batch of parts. If anyone has any feedback, let me know here or send me an email directly.
Hmmm... this is challenging one.
Anodizing is an option, but I would have to charge more for them to cover the added costs.
Sparkle silver powder (glossy) is another option:
I have one L5 in black left. I also have one L5X frame left, but it won't be available until I get more side covers made.
I recall reading that Larry said the HDPLEX 200W will start shipping at the end of July. I would preorder if you want one?
Last edited:
Doesn't take long for a small batch to be sold out when a few customers order more than one.
Thank you for spotting that and posting!
Last edited:
not a rgb fan, but that looks clean! (except that 2.5 drive, can be easily fixed with some m.2 drives.)
Would love to see a non-brushed finish, I'd gladly pay the extra money. Maybe I'm not the only one ?
(Silver L4 case)
If it's too much of an hassle I'd go with white.
I know I will have white available. I'll send you a PM about the other option.
3-4 weeks.
80mm fan mounting to Meanwell RPS-200 power supply by theHACK
Allows you to install RPS-200-12-C inside the Lone Industries L5.J-hackcompany.com
www.thingiverse.com
Last edited:
Wait, so you can have one fan and the 200 Meanwell inside?? ?80mm fan mounting to Meanwell RPS-200 power supply by theHACK
Allows you to install RPS-200-12-C inside the Lone Industries L5.J-hackcompany.com
80mm fan mounting to Meanwell RPS-200 power supply by theHACK
Allows you to install RPS-200-12-C inside the Lone Industries L5.J-hackcompany.com
www.thingiverse.com
No.
The height of the psu is about 105mm so it cuts into the spacing of the second fan.
After having a new set of panels for a few weeks, I finally found time today to make the swap. I originally purchased the Batch 1 silver/black combo (slightly bent, but this was a known issue) and have been really impressed with the case. I was a bit disappointed in the original silver color as I was hoping of something closer to the color of my silver NCase M1, however I loved the thick powder coated finish on the L5! When James launched the second batch of panels in white, I knew I wanted to switch my panels out. I thought I would post a few pictures for everyone to see the difference in finish and hole size between the two batches. As far as the difference in panel quality between the two batches, the minor bend in the first batch never really bothered me, but I do think Batch 2 lines up better along the seam down the side.
The original silver is a satin finish with some reflectivity and an almost industrial aesthetic, but the new white panel is totally matte and looks really beautiful! I think the new mesh pattern looks more restrictive, but I doubt it will make much of a thermal difference. It also hides the internals from view a little better if that's what you're in to. On to the pictures!
The original silver is a satin finish with some reflectivity and an almost industrial aesthetic, but the new white panel is totally matte and looks really beautiful! I think the new mesh pattern looks more restrictive, but I doubt it will make much of a thermal difference. It also hides the internals from view a little better if that's what you're in to. On to the pictures!
Similar threads
