Production FormD T1 Classic (READ FIRST POST)

[TSOF]

So I'm clear on this: can the tx240 be mounted with 1x15mm and 1x25mm underneath it (radiator closest to top panel)?

And if so, is it just tight, or does it actually foul on the top panel? If it fouls, do you reckon this could be modified in anyway to work?

Thanks.

 

[element72]

So I'm clear on this: can the tx240 be mounted with 1x15mm and 1x25mm underneath it (radiator closest to top panel)?

And if so, is it just tight, or does it actually foul on the top panel? If it fouls, do you reckon this could be modified in anyway to work?

Thanks.

This the setup most people should be doing. Yes.

One side note: I'm not sure how you can do 2x15mm and a 25mm with tx250. Someone just mentioned this was possible. I never heard of that. Probably will cause a 3mm bulge at the top. I would like to see a pic of that.

 

[Chaca]

I remember this being posted before: https://www.aliexpress.com/item/1597148545.html

Just one question. Will the 24 V rating be an issue for PC use? Unsure if it needs 24 volts or can handle up to 24 volts... As far as I know a regular PC power switch uses 5 volts. Not an electrician so sorry if this is a stupid question ?

 

[DrHudacris]

So I'm clear on this: can the tx240 be mounted with 1x15mm and 1x25mm underneath it (radiator closest to top panel)?

And if so, is it just tight, or does it actually foul on the top panel? If it fouls, do you reckon this could be modified in anyway to work?

Thanks.

There are these aligning rails on the top panel that might cause issues. Honestly not sure the best solution to get around this... But this is the only hurdle. Maybe hammering the radiator shroud down a bit?

This the setup most people should be doing. Yes.

One side note: I'm not sure how you can do 2x15mm and a 25mm with tx250. Someone just mentioned this was possible. I never heard of that. Probably will cause a 3mm bulge at the top. I would like to see a pic of that.

Yeah I'm the guy!

 

[gwertheim]

Any chance shipping to other countries? I really want this case but my country is not on the list. (Cyprus)

Countries will be added at a later date

 

[FunkEngine]

Does the two tone still have the usb c port and card reader or was that scrapped entirely?

 

[posure]

Does the two tone still have the usb c port and card reader or was that scrapped entirely?

That's a future accessory, not part of the main case.

 

[stanleyguan]

Anybody crazy enough to think of cramming this rad in? Looks like it's 40mm wide (i.e. 2 slots). With 3-slot config and a watercooled GPU, it might *just* fit in between the GPU waterblock and the panel? It might be possible to have 3 40mm fans too.

It might not make a groundbreaking difference to thermals. Just thinking about what's possible.

 

[DrHudacris]

Anybody crazy enough to think of cramming this rad in? Looks like it's 40mm wide (i.e. 2 slots). With 3-slot config and a watercooled GPU, it might *just* fit in between the GPU waterblock and the panel? It might be possible to have 3 40mm fans too.

It might not make a groundbreaking difference to thermals. Just thinking about what's possible.

I think with creativity (and maybe a 3d printer) you can fit it. You'll have to go with 6mm ID tubes, if I'm reading the specs right.

 

[TSOF]

I think you could fit it in, but the noise from 3-6x40mm fans?! ?

 

[FunkEngine]

That's a future accessory, not part of the main case.

Is that just for the electronics or will you need a new front panel with cut outs?

 

[thelaughingman]

@DrHudacris that stock cables look close to touch the 25mm fan! may I ask what is the actual clearance do you have there? do you think low profile connector / slim cables can give more clearance? Asking to see if there's 7mm to gain for my EK AIO 240 hahaha

 

[Ashenfall]

The TX240 is a 22fpi copper radiator. According to @fabio's testing, is also about 1-2 degrees cooler.

@ManaNeko had concerns about the LT240 rad not being very thick so my answer was specifically targeted at that. the TX240 is thinner than the LT240 so I didn't see a need to mention it

1-2 degrees is kind of negligible. Could even be within error margins of the test equipment

 

[DrHudacris]

@ManaNeko had concerns about the LT240 rad not being very thick so my answer was specifically targeted at that. the TX240 is thinner than the LT240 so I didn't see a need to mention it

1-2 degrees is kind of negligible. Could even be within error margins of the test equipment

You wondered if there was a 240mm radiator "at or under 27mm, full copper, with higher FPI" I don't see how my mentioning the TX was unnecessary.

 

[Ashenfall]

You wondered if there was a 240mm radiator "at or under 27mm, full copper, with higher FPI" I don't see how my mentioning the TX was unnecessary.

Ah , I see where i went wrong. I neglected to mention "thicker than the LT240". My bad

 

[Revolution]

It just me or the delivery date change from 17 to 24?

 

[PKAWA]

57 for the gpu under load is pretty good.

It just me or the delivery date change from 17 to 24?

No you're not wrong

 

[thelaughingman]

It just me or the delivery date change from 17 to 24?

it's changed for me too, and now there's also delivery option for 31

 

[gwertheim]

it's changed for me too, and now there's also delivery option for 31

Multiple shipments?

 

[thelaughingman]

Multiple shipments?

from playing with the options it currently looks like:

• Black - riser or no riser, ships 24
• Two-tone - riser or no riser, ships 31