Production FormD T1 Classic (READ FIRST POST)

[Wahaha360]

Is the two tone going to be black and silver or space gray and silver? I thought it was going to be the latter, but the website says “black and silver”

Black and Silver two tone first.

Space gray that I want cost too much, so maybe a limited run later (it will cost extra $50 to $100 to get that color with fingerprint resistance)

 

[hetvler]

Is the two tone going to be black and silver or space gray and silver? I thought it was going to be the latter, but the website says “black and silver”

Website? Did I miss something?

 

[blorkborkey]

SIDEARMD

Here's your gift card!

sidearmd.com

its a little buggy with a few things, but has some of the pictures and info

 

[hetvler]

SIDEARMD

Here's your gift card!

sidearmd.com

its a little buggy with a few things, but has some of the pictures and info

very neat! Thanks!

 

[chyll2]

I love you guys but is it really the first consumer CnC aluminum Case?

 

[gwertheim]

I love you guys but is it really the first consumer CnC aluminum Case?

It could be or it could be like one of those world's best pancakes signs.

 

[Wahaha360]

I love you guys but is it really the first consumer CnC aluminum Case?

the website is WIP, just ignore until we actually launch

 

[Aviswa]

@Wahaha360 Any updates on anodizing and launch?

 

[forstsiven]

Black and Silver two tone first.

Space gray that I want cost too much, so maybe a limited run later (it will cost extra $50 to $100 to get that color with fingerprint resistance)

Just to confirm, t1 won't fit mdtx, right? Not sure if there's clearance w/ 120mm rad.

 

[gwertheim]

Just to confirm, t1 won't fit mdtx, right? Not sure if there's clearance w/ 120mm rad.

The case cannot physically fit mdtx if I'm not mistaken

 

[DrHudacris]

Just to confirm, t1 won't fit mdtx, right? Not sure if there's clearance w/ 120mm rad.

Which DTX Motherboard did you have in mind? Impact has a 80+mm SODIMM riser card, forget about it. Then there's the issue of standoffs; the MB tray would need a completely different set of stand offs lower down, as the extra height of the DTX form factor is directed up (using the picture @Wahaha360 posted). To use the same standoffs as an ITX Motherboard would leave the extra height of a DTX board sticking out of the top of the case. Not to mention the PCIe riser card would likely need to be a bit longer. Many have dreamed about DTX in a sandwich layout, it is just not practical to adapt an ITX sandwich layout to accommodate a DTX.

 

[Necere]

To illustrate, MDTX needs 33mm of additional clearance compared to ITX:

 

[DrHudacris]

To illustrate, MDTX needs 33mm of additional clearance compared to ITX:

Picture is worth a thousand words! Ncase M1 being standard layout is best bet for a mDTX build

 

[zzmadd]

To illustrate, MDTX needs 33mm of additional clearance compared to ITX:

Upward...it extend over the riser..

 

[JayRello]

To illustrate, MDTX needs 33mm of additional clearance compared to ITX:

Picture is worth a thousand words! Ncase M1 being standard layout is best bet for a mDTX build

I think the Lazer3D LZ7 XTD would work with mDTX as well.

 

[baratheonbbq]

Where is the bracket for 2.5in drives?

 

[forstsiven]

Picture is worth a thousand words! Ncase M1 being standard layout is best bet for a mDTX build

Hah, I've got one already.

 

[hetvler]

I got my wisdom teeth removed earlier today and I’ve been informed I asked if the case had been released while I was under ?

 

[Vaux]

Checking re-anodizing next weekend. Then I will know if we can sell.

I turned off products on SFFLAB.

So... any news? ?

I know you're busy but that would be nice if you can give a little more information on when the case will launch so people can know if they can buy components now (when they're good deals on them) or if they should wait

 

[0x3F2D]

Will it be possible to pay with PayPal on sidearmd.com?