crossing fingers now so you can have everything back :/
WTF man, that's horrible! Can you at the very least file a claim to get reimbursed for the value?
Well... I tried to insert this, but it wouldn't work... the feeling remains the same.
https://media.giphy.com/media/BIN2S0sgQwdeE/giphy.gif
Damn, I hope they can reimburse you/ this doesn't put the whole project too far back. But that really sucks.
Hey man, did Lufthansa find your precious luggage?? I hope yes!! Eager to receive updates on this amazing case!
There might be hope, they find something in Munich that matches my suitcase description.
I’m working on USB-C spec now.
Prototype two should start this weekend.
I found a USB-C hub on Taobao. Lazer3D and I have been exploring the variations of this hub for our projects.
There are 3 configuration of this hub that is interesting (all powered by the same chipset GL3520):
1. 2x USB-A 3.0 + 2x USB-C 3.0
2. 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
3. 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack
These 3 I/O boards also happen to have the same screw hole mounting location, so in theory, if designed properly, customers can choose the I/O that best fit their needs.
* 2x USB-A 3.0 + 2x USB-C 3.0
* 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
* 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack, curtesy of Lazer3D K888D
* All powered by the same chipset GL3520
If all goes well, this could be standard part across other projects on this forum.
There are 3 configuration of this hub that is interesting (all powered by the same chipset GL3520):
1. 2x USB-A 3.0 + 2x USB-C 3.0
2. 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
3. 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack
These 3 I/O boards also happen to have the same screw hole mounting location, so in theory, if designed properly, customers can choose the I/O that best fit their needs.
* 2x USB-A 3.0 + 2x USB-C 3.0
* 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
* 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack, curtesy of Lazer3D K888D
* All powered by the same chipset GL3520
If all goes well, this could be standard part across other projects on this forum.
Last edited:
I am wondering if a passive GPU cooling setup with the accelero or Morpheus will work? The internal free volume of the case is very small and should facilitate rapid air exchange. 2 25mm fans will direct air from the bottom, one through an 120 rad, to the top passing through a bare Morpheus heatsink .
Are those potential alternatives to the 2 USB-C+USB-C Style Power Button in the original design or are they meant to replace them?I found a USB-C hub on Taobao. Lazer3D and I have been exploring the variations of this hub for our projects.
There are 3 configuration of this hub that is interesting (all powered by the same chipset GL3520):
1. 2x USB-A 3.0 + 2x USB-C 3.0
2. 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
3. 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack
These 3 I/O boards also happen to have the same screw hole mounting location, so in theory, if designed properly, customers can choose the I/O that best fit their needs.
* 2x USB-A 3.0 + 2x USB-C 3.0
* 2x USB-A 3.0 + 1x USB-C 3.0 + 1x SD Card
* 2x USB-A 3.0 + 1x USB-C 3.0 + 2x Audio Jack, curtesy of Lazer3D K888D
* All powered by the same chipset GL3520
If all goes well, this could be standard part across other projects on this forum.
The USB-C shaped Power Button Switch might not be tensioned enough to be satisfying. So I’m open to a new direction.
My gripe with the hub is the necessity of the SATA connector on the back for the current chipset.
I would prefer the entire hub power and data to be driven by a single connector, instead of multuple.
It’s not going to happen on the old USB3.0 20pin, so I’m thinking maybe USB 3.1 Gen 2 20pin Type-E
I'm planning to get a Mirrorless this year, so SD Card support is on my mind too.
I believe the SATA power connector is to provide the 25w of power to give the USB C it's fast charge ability.
I've used the USB A ports without the SATA power cable connected without issue.
YES! So happy for you man!!!I got my luggage back
Similar threads
