it is a thread introduce how G-uniq U0 exprience suite works and the way install the psu set into the enclosure.
the G-uniq U0 experience suite includes two main parts,the PSU part :archdaemon directplug,MB tray,PCIE&Power Distributed riser card,cable set(8pin CPU,8pin PCIE),ultimate modded Brick(from 300w to 600w) and 1.8M sleeved 8awg silicone dc cable,here are archdaemon directplug,MB tray,PCIE&Power Distributed riser card:
another view:
U0 suite come with special one-wired version archdaemon limited as main control unit:
the current ability of the power distribution:
code name is U0 FE(Fans Edition):
input DCjack is XT90H which can handle continuous 45Amper:
use dual XT60(30 Ampera each)output :
PCIE(90' angle type)to VGA card:
gold plated pcie riser card full speed pci-e 16x 3.0 with robust stablity:
and its console type enclosure:
the structure is so simple,only 2 pieces:
case width 313mm:
case depth:223mm
case thickness:63.5mm
so total volume is about 4.4L
it side panel is made of pcb with one side black and one side white,you can decide which side facing outside:
dcjack mounting in the middle of the rear:
let's start install the suite:
step 1:
prepare all your hardware,ram,cpu,heatsink,M2 ssd etc.the case support 42mm height cpu cooler:
step 2: place the MB on the MB tray and fasten the screws:
step 3: plug the archdaemon limited and cpu connector:
step4: manage the cable:
make sure the cable beneath the mb route without conflict:
the rear:
step 5: plug the riser card:
prepare the case:
step 6:
un screw the red one and orange one on both sides:
step 7: lift the upper cover at the rear of the case:
step 8:
seperate top cover from the front:
then take off the side panel of the vga side:
step 9:
place the MB tray on the bottom of the case:
fastened the dcjack:
step 10: prepare your vga card(here is Zotac 1080ti mini as demo)
step 11: insert the vga card with cable into the pcie riser card:
step 12: connect XT60:
step13: install back the side panel of the vga side:
step 14: fasten the VGA IO:
step15:
connect the power switch and power led:
step16: roooute the wire:
step 17:
install the top cover from the front of the case:the structure acts as a hinge:
step 18: close the top cover:
step19:fasten all screws back:
step20: plug the dc cable and the brick
the G-uniq U0 experience suite includes two main parts,the PSU part :archdaemon directplug,MB tray,PCIE&Power Distributed riser card,cable set(8pin CPU,8pin PCIE),ultimate modded Brick(from 300w to 600w) and 1.8M sleeved 8awg silicone dc cable,here are archdaemon directplug,MB tray,PCIE&Power Distributed riser card:
another view:
U0 suite come with special one-wired version archdaemon limited as main control unit:
the current ability of the power distribution:
code name is U0 FE(Fans Edition):
input DCjack is XT90H which can handle continuous 45Amper:
use dual XT60(30 Ampera each)output :
PCIE(90' angle type)to VGA card:
gold plated pcie riser card full speed pci-e 16x 3.0 with robust stablity:
and its console type enclosure:
the structure is so simple,only 2 pieces:
case width 313mm:
case depth:223mm
case thickness:63.5mm
so total volume is about 4.4L
it side panel is made of pcb with one side black and one side white,you can decide which side facing outside:
dcjack mounting in the middle of the rear:
let's start install the suite:
step 1:
prepare all your hardware,ram,cpu,heatsink,M2 ssd etc.the case support 42mm height cpu cooler:
step 2: place the MB on the MB tray and fasten the screws:
step 3: plug the archdaemon limited and cpu connector:
step4: manage the cable:
make sure the cable beneath the mb route without conflict:
the rear:
step 5: plug the riser card:
prepare the case:
step 6:
un screw the red one and orange one on both sides:
step 7: lift the upper cover at the rear of the case:
step 8:
seperate top cover from the front:
then take off the side panel of the vga side:
step 9:
place the MB tray on the bottom of the case:
fastened the dcjack:
step 10: prepare your vga card(here is Zotac 1080ti mini as demo)
step 11: insert the vga card with cable into the pcie riser card:
step 12: connect XT60:
step13: install back the side panel of the vga side:
step 14: fasten the VGA IO:
step15:
connect the power switch and power led:
step16: roooute the wire:
step 17:
install the top cover from the front of the case:the structure acts as a hinge:
step 18: close the top cover:
step19:fasten all screws back:
step20: plug the dc cable and the brick
Last edited: