Production CONSOLE and CONSWOLE: entry level 2-slot and 3-slot console cases! [Available Now!]
- Thread starter KSliger
- Start date
Is it possible to mount 25mm fans on the top of the gpu in the 3 slot version of the case?
I have this setup for my GPU in the Node 202 and it really helps with the case temps with it pulling hot air out of the case and I think it would be great for the Console as well.
That or have the PCIe mount on the back of the Console a screwed in plate so that the user can reverse the orientation to have the GPU to face the 2 fans in the shroud and keep the ability to use the 3rd slot for some other PCIe expansion as well. I don't know how feasible that would be cost wise but that would be a great option to have for the case.
Definitely getting one on release, love this form factor
I have this setup for my GPU in the Node 202 and it really helps with the case temps with it pulling hot air out of the case and I think it would be great for the Console as well.
That or have the PCIe mount on the back of the Console a screwed in plate so that the user can reverse the orientation to have the GPU to face the 2 fans in the shroud and keep the ability to use the 3rd slot for some other PCIe expansion as well. I don't know how feasible that would be cost wise but that would be a great option to have for the case.
Definitely getting one on release, love this form factor
Is it possible to mount 25mm fans on the top of the gpu in the 3 slot version of the case?
I have this setup for my GPU in the Node 202 and it really helps with the case temps with it pulling hot air out of the case and I think it would be great for the Console as well.
That or have the PCIe mount on the back of the Console a screwed in plate so that the user can reverse the orientation to have the GPU to face the 2 fans in the shroud and keep the ability to use the 3rd slot for some other PCIe expansion as well. I don't know how feasible that would be cost wise but that would be a great option to have for the case.
Definitely getting one on release, love this form factor
Check out page 4, they are doing one better. Two slim 120mm fans mounted behind the GPU so air is pulled through one end and exhausted out the other.
I am going to instantly preorder the SWOLE.
It sounds almost too good to be true.
Barely more volume than a node 75mm CPU cooler, 3 slot GPU, 145mm height and 330mm length.
Hit's every single one of my boxes, and more ventilation is always nice.
Targeted price is good too.
It sounds almost too good to be true.
Barely more volume than a node 75mm CPU cooler, 3 slot GPU, 145mm height and 330mm length.
Hit's every single one of my boxes, and more ventilation is always nice.
Targeted price is good too.
Is anyone really planning to lay this case flat, or would upright (takes up less desk space) be the primary way you'd orient it?
Asking because 3-slot version is really hard to make look remotely decent laid down, but I can do a pretty unique / modernish design when upright:
Asking because 3-slot version is really hard to make look remotely decent laid down, but I can do a pretty unique / modernish design when upright:
For me I'd stand it upright. Personally I'm not a huge fan of the slab base on the smaller model like initially portrayed. I prefer a foot like stand of the sentry/salvo models. But I appreciate the cost efficiency of the flat slab for sure.Is anyone really planning to lay this case flat, or would upright (takes up less desk space) be the primary way you'd orient it?
Asking because 3-slot version is really hard to make look remotely decent laid down, but I can do a pretty unique / modernish design when upright:
I like the new version. It looks as if the case will get plenty of air from below with it raised up as you show.
Last edited:
I'd most likely utilize this chassis in its upright orientation to minimize the footprint. That said, I'm not even sure that a 3-slot thick chassis would fit into all that many entertainment centers laid flat anyway for that matter.
Is it stable upright? Tip-over proof?
Can you share some of your omni-directional designs?
I personally would fashion some magnetic feet myself, so if it's side mounting feet you're worried about breaking the aesthetic don't do that.
I'm one of those people anxious about my computer falling over.
Can you share some of your omni-directional designs?
I personally would fashion some magnetic feet myself, so if it's side mounting feet you're worried about breaking the aesthetic don't do that.
I'm one of those people anxious about my computer falling over.
that doesnt look that bad laying on the side , I am fine with either standing or laying downIs anyone really planning to lay this case flat, or would upright (takes up less desk space) be the primary way you'd orient it?
Asking because 3-slot version is really hard to make look remotely decent laid down, but I can do a pretty unique / modernish design when upright:
I was definitely thinking of laying this flat but I was also leaning more towards the smaller Console version, not necessarily the chunkier version. Was probably going to lay it flat using it hooked up to my TV. Granted, the cabinetry below my TV has moveable shelving so I could probably fit the chunky version flat too.Is anyone really planning to lay this case flat, or would upright (takes up less desk space) be the primary way you'd orient it?
Asking because 3-slot version is really hard to make look remotely decent laid down, but I can do a pretty unique / modernish design when upright:
Then again, I'd probably get the vertical stand too in case I ever moved the case around too, but at least right now I'd probably be using either version laying flat.
Will probably keep the case almost identical to post on page 4, just changed the front panel to not use screws.
I increased the density of them vs all other holes on the case, won't look too odd but will help airflow.
I will include adhesive feet with every unit, save your $.
The 2-slot is very unstable without the flat base, doubt the 3-slot will be a whole lot better.
Doing a couple different ideas for the base, will post tomorrow.
Unfortunately this was not very stable based on CoM math, will have to make a future larger cases based on that design.
Rolling back to the original flat base plate for now due to the low cost and high stability. Tried a few different bend ideas and they all seem likely to scratch furniture or add $ to price for no reason.
Really trying to keep these focused on that lower price target.
I increased the density of them vs all other holes on the case, won't look too odd but will help airflow.
I will include adhesive feet with every unit, save your $.
The 2-slot is very unstable without the flat base, doubt the 3-slot will be a whole lot better.
Doing a couple different ideas for the base, will post tomorrow.
Unfortunately this was not very stable based on CoM math, will have to make a future larger cases based on that design.
For me I'd stand it upright. Personally I'm not a huge fan of the slab base on the smaller model like initially portrayed. I prefer a foot like stand of the sentry/salvo models. But I appreciate the cost efficiency of the flat slab for sure.
Rolling back to the original flat base plate for now due to the low cost and high stability. Tried a few different bend ideas and they all seem likely to scratch furniture or add $ to price for no reason.
Really trying to keep these focused on that lower price target.
I'd add "T H I C CON S W O L E" as a choice, just so I can giggle every time I look at it when I buy it ?
