SKYREACH 4 MINI (S4M)
- Thread starter Josh | NFC
- Start date
CPU: Ryzen 1600, OC +0.025V
GPU: GTX 1050 ti OC +50mV
RAM: 16 GB DDR4
MB: Mini itx 350 asrock
Others: M2, mouse, keyboard, 1080p 75 fps monitor, etc.
So, I looked up the recommendation from NFC on dynamo mini and dell 330, but I just don't get it. Dynamo mini is 160 DC? How is that enough power to handle this? From using several watt calculators online, they seem to hover around 280 recommending 450 W psu.
Also the recommendation of dellda330pa111, I can't seem to find one. Only one I managed to find was $165. I found an alienware 330w ac adapter for $65.
Also, is the dell 330 able to be inside the case? How do you differentiate which ac adapters are good enough?
GPU: GTX 1050 ti OC +50mV
RAM: 16 GB DDR4
MB: Mini itx 350 asrock
Others: M2, mouse, keyboard, 1080p 75 fps monitor, etc.
So, I looked up the recommendation from NFC on dynamo mini and dell 330, but I just don't get it. Dynamo mini is 160 DC? How is that enough power to handle this? From using several watt calculators online, they seem to hover around 280 recommending 450 W psu.
Also the recommendation of dellda330pa111, I can't seem to find one. Only one I managed to find was $165. I found an alienware 330w ac adapter for $65.
Also, is the dell 330 able to be inside the case? How do you differentiate which ac adapters are good enough?
Hello, zph0eniz
Ryzen 1600 pulls about 65w
1050ti Mini pulls a MAX of 75w
So you end up, theoretically, at about 135w power draw + your perherpials.
In reality, I expect you to pull about 125w at 1080p. Now for your overclock...I dunno. If you want to play it safe go with the HDPLEX 400, but honestly I think you would be fine with the Dynamo mini/HDPLEX 160.
As for the Dell brick, yes, you want the expensive one FROM DELL. This is me saving you a few minutes of searching on the forum. If you want to go with a cheaper one then you need to do some research. It will not fit inside the case. You need a different PSU for that, the HDPLEX 160 AC/DC. It should be good for your build, but again, overclocking...you might want to go for the bigger external brick.
Peace
Can anyone tell me the height of the motherboard standoffs that comes pre-installed on the Skyreach 4 mini? Thanks!
Will Ryzen 2400G fit with the fan, along with two Trident Z 16 x 2 GB ram? If not, any videos to remove the fan? I bought the noctua low profile fan and I would much rather use that if it's less noisy.
Last edited:
The HP Omen X 330W is 19.5v 16.92A; 100-240v
Yes and it works well to boot! Been testing it and having some customers switch over. So far so good.
Oh, cool. Thank you. I didn't see specs on the official HP page, so I think I was looking at the Microcenter product page, where it said it's 12v 27.5a. Must be a different unit I saw.
Last edited:
Good to know. It doesn't look like its any cheaper than the Dell, but it is a little prettier, IMO. Does it run cooler?
Cuban Legend has been telling people that the dell 330W is better than the HP voodoo omen. Any reasons why?
They operate at different voltage. Voodoo will not work on g-unique models. Not sure about hdplex.
I think he is talking about the old Voodoo 350, not the new Omen X.
At any rate I prefer the GENUINE Dell because it is more portable.
It was a joy to build and I'm happy with the results. The 140mm fan on top keeps everything cooler during gaming.
Last edited:
I’ve seen OC videos on YouTube, power draw of an OC 2200g doesn’t go past 120 Watts I believe. Could be lower but I don’t remember the things so well.
Here's the full breakdown. Easier to view it here on pcpartpicker: https://pcpartpicker.com/b/2VLJ7P
Similar threads
