First week of March, I need to finalize T1 Classic V1.2 first (very close)
-
Save 15% on ALL SFF Network merch, until Dec 31st! Use code SFF2024 at checkout. Click here!
Concept FormD T1 V2.0
- Thread starter Wahaha360
- Start date
Any super secret rumors on if say PSlate or similar custom cables would still work?
Just planning ahead...and wonder if I miss out on the RMA stock drop, if such aftermarket length custom cables would work with the new revision
Agree with this confusion. Is there any great differences between v1.2 and 2.0 (aka EVO) like form factor? If not so which one should I wait? I am not rich enough for both. What can help me to mace this decision? I noted that the only significant feature is 240 AIO support
My impression from reading W360's comments is that T1 v1.2 is the same size as v1.1 with only minor changes while T1 EVO is like anything is possible
Take a chill pill and wait for a prototype to see what he comes up with.
I think you are referring to T1V1.1 reserve we held, those are the same as T1V1.1, so the cables should work.
My impression from reading W360's comments is that T1 v1.2 is the same size as v1.1 with only minor changes while T1 EVO is like anything is possible
Pretty much biopunk said.
I made the T1 V1.2 because enough people reached out to me asking a continuation of T1 V1.1. So I greenlighted V1.2 as an update to V1.1.
This also give us more room and reason to break away from T1 for V2.0 EVO. Just more creative freedom.
Last edited:
I was more wondering if the T1v1.2 would end up with different cable lengths versus T1v1.1; in case the RMA stock release sells through before I can snag a Ti one.
Planning ahead, as I've noticed this trend with PSlate that whenever there's a Formd stock drop he goes out of stock really fast.
Last edited:
Ok, Whatever it will be, v1.2 or v2.0, I just can't wait the moment when orders or preorders will be opened again and I can make a purchase and start to build my new PC! Just because you are the best on the market and I don't want to accept any alternatives.
T1 EVO should no longer be in the original P1 price bracket, instead IMO it will be in the 200-250USD bracket just like the T1 Classic. Whether price goes up or down and how much depends on a couple of factors - raw material price increases vs. cheaper cost to manufacture due to lower rejects as Wahaha is going to optimised the manufacturability aspect of the design.
Is there any succinct post that explains the planned differences between the 1.1, 1.2 and EVO?
Nope, no one even knows what the EVO is gonna be yet
@Wahaha360 WoW! I am so excited for this EVO project, the case looks very nice!
I am one of the lucky guys who got a Gunmetal T1 from maybe its final batch. After I finished the build, I do have a suggestion for the new project if it resembles the T1 V1.1 in its inner design.
Specifically, before I got the case the only CPU I bought is 5950x which turns out to be a heat generating monster. Because I am a lazy guy, AIO is always my first choice, and I eventually went for EK AIO 240 Basic for better cable management. If I configure the cooling system as top exhaust and put two fans (one 120mm x 15mm and one 120mm x 25mm Noctua Chromax) below the radiator, at stock, the idle temp for CPU is about 50-60 C and the load temp could go as high as 95 C, which is obviously too high.
Therefore, I decide to go for the three-fan push and pull top exhaust config by putting two 120mm x 15mm fan on the top of the rad and one 120mm x 25mm below it on the PSU side (shown in the 1st fig).
Now, the main problem is that, if your rad has straight corners as my rad has, you cannot stick the rad to touch the front panel (I circle the part with red stroke) to make enough room for the 120mm fan below the rad. I did it by polish the bottom fan so that it has several dents on the front panel side to fit those tubes. However, that is painful...
The main reason you cannot stick a straight corner rad to the front panel is because the front panel has those rounded notch as highlighted in the 2nd picture. If you force to put the rad in those notches, the rad will be bumped up a little bit and you cant close the top panel.
Idk if it is an easy fix, I just want to share my experience and hope this can help you in the new project. Overall, I still think T1 is the best SFF case currently in the market, and I really love it!
I am one of the lucky guys who got a Gunmetal T1 from maybe its final batch. After I finished the build, I do have a suggestion for the new project if it resembles the T1 V1.1 in its inner design.
Specifically, before I got the case the only CPU I bought is 5950x which turns out to be a heat generating monster. Because I am a lazy guy, AIO is always my first choice, and I eventually went for EK AIO 240 Basic for better cable management. If I configure the cooling system as top exhaust and put two fans (one 120mm x 15mm and one 120mm x 25mm Noctua Chromax) below the radiator, at stock, the idle temp for CPU is about 50-60 C and the load temp could go as high as 95 C, which is obviously too high.
Therefore, I decide to go for the three-fan push and pull top exhaust config by putting two 120mm x 15mm fan on the top of the rad and one 120mm x 25mm below it on the PSU side (shown in the 1st fig).
Now, the main problem is that, if your rad has straight corners as my rad has, you cannot stick the rad to touch the front panel (I circle the part with red stroke) to make enough room for the 120mm fan below the rad. I did it by polish the bottom fan so that it has several dents on the front panel side to fit those tubes. However, that is painful...
The main reason you cannot stick a straight corner rad to the front panel is because the front panel has those rounded notch as highlighted in the 2nd picture. If you force to put the rad in those notches, the rad will be bumped up a little bit and you cant close the top panel.
Idk if it is an easy fix, I just want to share my experience and hope this can help you in the new project. Overall, I still think T1 is the best SFF case currently in the market, and I really love it!
Just wondering whether the April target was for the 1.2 or the Evo? Thanks
At this stage of development, can we have some statements about how the EVO will set itself apart from Meshlicious?
