Mentioned this on Reddit someone asked the same question. It's simple to fill the LT Solo via the port, disconnect CPU 8 pin uninstall the LT SOLO you should have enough slack to bring the LT SOLO to the highest point to ensure you are able to fully fill the loop. Cycle PC until the loop is filled. Re-Install LT SOLO.
-
Save 15% on ALL SFF Network merch, until Dec 31st! Use code SFF2024 at checkout. Click here!
Mentioned this on Reddit someone asked the same question. It's simple to fill the LT Solo via the port, disconnect CPU 8 pin uninstall the LT SOLO you should have enough slack to bring the LT SOLO to the highest point to ensure you are able to fully fill the loop. Cycle PC until the loop is filled. Re-Install LT SOLO.
which TPV QDC do you have? the older HF one or newer ES one? since I'm already using the Eisstation 40 the point is kinda moot for me now.
But before when I was considering non-Alphacool, i.e. EK ZMT + Quantum Torque + DDC setup, the solution I came up with was putting a Torque T fitting + a ball valve at the lowest point in the loop (along the bottom of the GPU chamber). It would be so simple to drain the loop, just turn the valve and coolant pouring out due to gravity. Then when it's time to fill, just flip the entire case and let gravity do the work again.
i have two of these currently and I really like them https://modmymods.com/alphacool-3-8...r-kit-tpv-eisbaer-compatible-black-17452.html but i want to try the new version but idk if I just want the compression. I like the slimmer form though. https://modmymods.com/alphacool-es-...or-kit-tpv-pushin-industry-version-17469.html
Yeah about that, I was wondering if I can't permanently attach a hose to the fillport of the LT240 CPU block and have that attached to the rear port with some sort of filler cap attachment that screws into the back port for easier draining and filling of the system.
That would be ideal.
I think the same too,I bought dan case A4 and ncase M1 without a shipping problem in the past.I hope we can solve he problem...
where are you based at? I'm in Vietnam and shipping between CN-VN is slower than CN-US despite the US being an ocean away while VN is next door neighbour. Go figures I guess.
Hey everybody, long time watcher of this forum. First time posting. I've seen a couple builds so far of this awesome case. I'm waiting for mine to arrive in the mail. Mine says it's coming from Guangzhou China and it's shipping to Canada. Has anyone else had any good experience shipping to Canada? I haven't seen any other posts about this destination. Curious if there were any problems or hoops you had to jump through.
Looks like Barrow have just released a cpu block/pump combo.... http://www.barrowint.com/news/x/1607.html
DDC?
DDC?
Exciting. I'm curious if they went nickel plated or full copper, and also what the overall height is.Looks like Barrow have just released a cpu block/pump combo.... http://www.barrowint.com/news/x/1607.html
DDC?
Seems like the other CPU/Pump block combo that @Wahaha360 is working on is on hold since it's been super quiet in that thread.
Another Canadian. Did you read at least 75 pages (370-445) before posting? You will know, many Canadian in here
Looks quite promising aside from the height though. Judging by this diagram the plane where the G1/4 ports are located is roughly 50mm in height. With Koolance's 20mm high swivel 90-degree adapter there is a chance that this might fit in a two-slot T1 but only barely.
Since I live in Germany, I use Aquatuning.de. I always had good experience with them and my last order went smooth. One part wasn't in stock and I got an email not even 24 hours after ordering. Also the support was very responsive (I wrote with them in German).
The item not in stock was the DC-LT 2600, so I decided to get my pump through a kit, that isn't much more expensive, but for some reason available earlier.
My biggest problem will be deciding on going for a 2070s or waiting for 3000/big navi, because my 1080 Gaming X will never get close to fit in the T1.
Why wouldn't the MSI Gaming X fit? Spec sheet states that it is 140mm tall.
@Wahaha360 put a evga 2080 ftw3 in and it is the same height
Looks like Barrow have just released a cpu block/pump combo.... http://www.barrowint.com/news/x/1607.html
DDC?
If anyone is interested here is the Taobao link for the OLED screen version. It's rather expensive of course.
I am hoping Optimum Tech sees this and posts a video on it.
Edit: Here is the other model.
By the way Canadians, your case is most likely coming tomorrow. check shipping details via Canada post.
@Chaca @Navic @Nero and anyone else that might order the same fittings I did:
I would add a 45 degree fitting or two. I got my fittings today and started fitting everything today to see how it would all fit. I was attempting to get my DC-LT 40 to be around the same height as @fabio to get that nice, clean tubing run from the GPU to the res. I wasn't able to do that with the fittings I got. You could add another extension fitting, but I will just use a 45 degree fitting.
Note: I am using the Alphacool 240 rad (the 25mm one). I used a rotary fitting with a 20mm extender fitting.
I would add a 45 degree fitting or two. I got my fittings today and started fitting everything today to see how it would all fit. I was attempting to get my DC-LT 40 to be around the same height as @fabio to get that nice, clean tubing run from the GPU to the res. I wasn't able to do that with the fittings I got. You could add another extension fitting, but I will just use a 45 degree fitting.
Note: I am using the Alphacool 240 rad (the 25mm one). I used a rotary fitting with a 20mm extender fitting.
With water block this thing is over 155mm high and i didn't factor in the pcie pins.
I will try to fit it, but i don't have high hopes.
Similar threads
