Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

[Mango]

Are high static pressure fans still recommended for bottom exhaust if going with vented side panels? There's not much clearance under the case but I don't know if that's considered "pressure" or too restrictive for silent high CFM low pressure fans like Arctic F12 PWM.

 

[KSliger]

Question - is there room to fit this pump/res combo in the SM580? If so, where? I know in @KSliger's diagram with measurements before, there was a place to put it up near the top but I can't visualize how it fits there.

It should fit on the back of the front of the case, just above the GPU and next to the PSU. I have a 3D model of it in the case there. Could also mount it on the outside rear of the case.

Here's an updated pic of my rig:

I had purchased an extra front panel and decided to give some painting a go. Thought it looked neat .

Should I just sell unpainted panel sets as an option?

Are high static pressure fans still recommended for bottom exhaust if going with vented side panels? There's not much clearance under the case but I don't know if that's considered "pressure" or too restrictive for silent high CFM low pressure fans like Arctic F12 PWM.

I would think higher static pressure fans would perform better at lower RPMs for exhaust mode with vented panels. But any fan should work fine.

 

[TheLobsterHatMan]

Should I just sell unpainted panel sets as an option?

I mean, I can't comment on the market of such an item, but I'd definitely appreciate unfinished panels .

 

[TheHawk1337]

Any news on the EU reseller? Planning on ordering this week, would be a bummer to find out a EU reseller is available next week

Besides that, any idea when the SM580 will be available? I prefer the 580 over the 560

 

[payo36]

My new SM550 Lot of pics
Just got it today. Thanks to KSliger for his service.

 

[wykydtronik]

My new SM550 Lot of pics
Just got it today. Thanks to KSliger for his service.

Do you think there's enough clearance in that case to fit a 240mm aio with dual slim 120mm fans? LOOKS SO GOOD MAN!!!

 

[ermac318]

Do you think there's enough clearance in that case to fit a 240mm aio with dual slim 120mm fans? LOOKS SO GOOD MAN!!!

No, that's what the SM570/580 are for.

 

[wykydtronik]

No, that's what the SM570/580 are for.

Right, but it looks like there is enough clearance for slim rad and radiator. I am wondering if there's enough space to clearance 37mm

 

[TheLobsterHatMan]

Right, but it looks like there is enough clearance for slim rad and radiator. I am wondering if there's enough space to clearance 37mm

It does not. There's barely enough room for full depth fans (25mm)

 

[wykydtronik]

It does not. There's barely enough room for full depth fans (25mm)

I am really curious as to how much space is between the riser and the fans. Also the clearance between the motherboard and the fans.

Although it would be nice to fit the fans inside the case; what I'm getting at is the possibility of mounting the fans externally in a push config.

Imagine this: 240mm AIO rad mounted inside (27mm thickness) and 2 x 120mm slim fans externally mounted in push config (12mm). Boom, AIO in the SM550. Custom loop, we could run a 20.5mm thick rad.

It seems like there is a slim chance this might work... ?

@payo36 thanks for posting those pics btw

 

[wsgroves]

@wykydtronik
That space is non existent. The fans are tough enough to get in there on their own. I thought about adding below the case and having a rad there but that will not work either.

 

[1s44c]

but @wykydtronik could get one of those 25mm xspc radiators... My concern would be the clearance between the fans and the desk/floor/etc.

 

[KSliger]

SM550 and SM560 are discount $10 in Carmine Red

 

[crag]

With Ryzen thermal info coming out and the chip I plan on running only being 65W I decided to skip watercooling for now and just went with the SM550. Can't wait to get it in, even if the rest of the parts for my build won't be here for another month+

 

[Maniac]

I think it's time that Sliger finally get its own Vendor sub-forum. @confusis? There is way to much info in this one monolith topic that covers a series of cases (plus the future ones), makes it very hard to find to proper information (especially if one has been away for a while .

 

[1s44c]

@KSliger Do you have an ETA for the SM 580?

 

[deadline]

@KSliger Will the SM570/580 be able to support the new Crosshair Mini DTX? Thanks!

 

[JaPeMo]

@KSliger Will the SM570/580 be able to support the new Crosshair Mini DTX? Thanks!

If you dont install above fans maybe you can install Mini DTX MB

 

[GerryMz]

With Ryzen thermal info coming out and the chip I plan on running only being 65W I decided to skip watercooling for now and just went with the SM550. Can't wait to get it in, even if the rest of the parts for my build won't be here for another month+

which ryzen are you planning to cool and with which cooler??

 

[wsgroves]

@KSliger Will the SM570/580 be able to support the new Crosshair Mini DTX? Thanks!

Yes, it will fit as far as I know. As long as you keep the space that the extra MB legnth takes up clear.

@Maniac Good idea. I second this. =)