Log Neath's Rigs: Too many different builds!

[Neathdrawls]

Managed to snag a B-Stock N-ATX v2, so while the P-ATX v3 is great, the CPU cooler limit might be too much for my 5950X.

Full album link here.

Not much trouble building the case and in the case, it being bigger than the P-ATX, it was very familar. Thermals wise, the AXP120-x67 is one of the best cooler for the N-ATX. There are tests in the main thread for the N-ATX v2.

Some pictuers of the test build before closing the panels and don't mind the ketchup and mustard cables from the Sunon fans. Doesn't exactly drop temperatures drastically, but seems to push air out in a more directed manner from the CPU and GPU.

All in all, a fantastic case!

Specifications (N-ATX v2)

• Case: SFFTime N-ATX v2 Black
• Processor: AMD Ryzen 9 5950X
• Motherboard: Gigabyte X570S Aero G
• Ram: 64(4x16)GB Corsair Vengeance RGB 3600 CL18
• PSU: Great Wall Hunter Nirvana 850W 80+Gold
• GPU: AMD Radeon RX 6800 XT 16GB Midnight Black
• Cooler: Thermalright AXP120-x67 (with Thermalright TL-B12S fan swap)
• Case Fan (Side Exhaust): Thermalright TL-B12S
• Case Fan (3x Top Exhaust, 2x Bottom Exhaust): Sunon MagLev 40x20mm
• Storage: 1x MSI Spatium NVMe 1TB
• Storage: 1x J2000 NVMe 2TB

Also, at the same time, with the P-ATX now vacant and selling my 11400 with the B560I board, I moved the FormD T1 reference build over.

Specifications (P-ATX v3 All Intel)

• Case: SFFTime P-ATX v3 Black
• Processor: Intel 11th Generation i5-11600K
• Motherboard: MSI Gaming Edge Wifi Z590
• Ram: 16(2x8)GB Team Group Xtreme ARGB 4000 CL28
• PSU: Cooler Master V850 SFX Gold
• GPU: Intel ARC A770 Limited Edition
• Cooler: ID-Cooling IS-55 ARGB (with Thermalright TL-C12015B-S fan swap)
• Case Fan (Side Exhaust): Thermalright TL-C12015B-S
• Storage: 1x Sabrent Rocket 1TB
• Storage: 1x YBMG 1TB

 

[Neathdrawls]

Finally getting around to this post.

Upgraded to a 4090, after a small scare with my RX 6800 XT, where I thought it died for a while. Actually, I also had to RMA the first 4090, as it suddenly died. No burnt pins on either the GPU side or the cable side, but thankfully the RMA with the local distributor was painless. One for one replacment on the spot.

Along the way, and I also upgraded the Great Wall Nirvana 850W to an ATX 3.0 PSU, the FSP Hydro G Pro 1000W, and with custom cables that made the cable management way easier. Changed out the three top mounted Sunon fans for actually good fans, Noctua NF-A40x20, and the two bottom Sunons for a Thermalright TL-B8.

Now the build is way more quiet. And fully maxed out.

Personally, I really like the look of a SFF case that is fully loaded, and packed to the brim. The ATX PSU at 150mm in depth is really the maximum that one should have if using a very tall card. As a full true 3 slot 4090, this is card is one of the only ones that will fit into the the N-ATX v2 while using an ATX board. Full ATX Motherboard, ATX PSU, 3 Slots 4090, full thickness 25mm case fans, making full use of (almost) all of the case.

Temperatures wise, the 4090 is one cool beast. Overbuilt and massive, and with a slight undervolt, temperatures while gaming at 3440x1400 on max settings in Darktide, temperatures don't go above 65C, with my ambient being usually 30C to 32C.

Small little problem I faced, it's either the PSU or the provided power cable. Probably a combination of both, but 95% on the PSU. What's the issue? The placement of the on/off switch of the FSP PSU is covered by the power extension cable. Not too sure if it is noticeable in the picture clearly though.

Some other pictures of the setup, and testing before closing the panels:

Specifications (N-ATX v2) v2

• Case: SFFTime N-ATX v2 Black
• Processor: AMD Ryzen 9 5950X
• Motherboard: Gigabyte X570S Aero G
• Ram: 64(4x16)GB Corsair Vengeance RGB 3600 CL18
• PSU: FSP Hydro G Pro 1000W 80+Gold - ATX 3.0 version
• GPU: Inno3D RTX 4090 3X
• Cooler: Thermalright AXP120-x67 (with Thermalright TL-B12S fan swap)
• Case Fan (Side Exhaust): Thermalright TL-B12S
• Case Fan (Bottom Exhaust): Thermalright TL-B8
• Case Fan (3x Top Exhaust): Noctua NF-A40x20 PWM
• Storage: 1x MSI Spatium NVMe 1TB
• Storage: 1x J2000 NVMe 2TB

 

[Elaman]

Temperatures wise, the 4090 is one cool beast. Overbuilt and massive, and with a slight undervolt, temperatures while gaming at 3440x1400 on max settings in Darktide, temperatures don't go above 65C, with my ambient being usually 30C to 32C

That is pretty amazing. Any idea of what power consumption could the 4090 have while reaching 65º?

 

[Neathdrawls]

That is pretty amazing. Any idea of what power consumption could the 4090 have while reaching 65º?

Around 250W to 290W. Granted I have undervolted the GPU too, around 2700Mhz @ 950mV.

 

[morj]

Gotten an aftermarket mounting bracket from Taobao for the AXP100 Full Copper, which allows the AXP100 to be rotated 90degrees

Hi! I can't seem to find it, can you please drop me a link? Thanks

 

[tinyitx]

Hi! I can't seem to find it, can you please drop me a link? Thanks

Are you looking for this?

taobao | 淘寶

淘寶（Taobao）讓您隨心淘超值商品，爲您提供流行服飾、美妝洗護、3C數碼、大小家電、家俬家居、箱包皮具、運動戶外、五金工具、玩具等千萬件熱銷好貨，淘寶支持文字或圖片搜索商品。天貓淘寶海外作爲Taobao面向華人的跨境電商平台，覆蓋200多個國家和地區的消費者，其中核心站點包括：淘寶香港（taobao hk）、淘寶台灣（taobao tw）、淘寶澳門、淘宝新加坡、淘宝马来西亚、淘宝韩国（타오바오 사이트）、淘宝澳洲、淘宝加拿大、taobao world。

www.taobao.com

 

[morj]

Are you looking for this?

Thanks a lot! I'm always struggling with the taoabao search...

 

[hubbiton]

New Year, new build right?

The FormD T1 Reference; such a beauty.

Full album is here.

How did you install 92mm side fan? 3D printed bracket double taped to side panel?

 

[Neathdrawls]

How did you install 92mm side fan? 3D printed bracket double taped to side panel?

There's a file to be downloaded from FormD website for the side bracket for 3D printing.

It then screws onto the case.

 

[hubbiton]

There's a file to be downloaded from FormD website for the side bracket for 3D printing.

It then screws onto the case.

Thanks! Completely forgot about 3d prints section. Is one screw mount sufficient? - no vibrations or noise?