Selling Custom 3D Printed low profile EKWB terminal

**** ON HOLD AS MY LAST ONE IS LEAKING AND I WANT TO MAKE SURE THEY DON'T BEFORE I SELL MORE ****


This block has official EKWB dimensions, I'm selling them for:

• $25 USD / each per color
• $40 USD / 2-pack same color
• $45 USD / 2-pack different color

These are printed in ABS and can be Black, Grey/Silver, White, Orange, Yellow, Purple, Magenta, Clear*, Blue or Tan/Gold.

*Clear ABS will stain and keep color apparent if you change colors.

They come tapped in G1/4 and inclue three shorter hex pan head M4 screws. Surfaces are sanded with 120, then 240 sand paper then rough polished on cloth. They are 10mm thick + screw head, If the user wants, there's enough room for using a drill bit to create a countersinked recess for countersunk screws, but you're on your own for that.

If you need a custom model for SLI/CrossFire, send me a PM.

 

[Duality92]

up

 

[Damascus]

Not interested in buying but it's great that this exists!

 

[chanberg]

definitely cool, but i wonder if there is any malformations or leaks after extended loads of hot fluid.

 

[Duality92]

a water loop should never have any hot fluids. Your delta T for loop temps should be like 10C above ambient for any PC watercooling coolant to keep doing it's job.

I discussed this with Mayhems before hand (sort of a friend of mine) and ABS is fine for a PC watercooling loop, appart from staining as it is a porous plastic. Hence, why I don't offer clear without a warning.

 

[Biowarejak]

I've made water cooling parts with an FDM printer before. I'd leak test these if you haven't already, because my own designs needed to be sealed.

 

[VegetableStu]

how long would ABS hold with water? o_o I hear filament hydration is a problem, so I'm not sure if this translates to already printed plastics ._.

 

[Biowarejak]

how long would ABS hold with water? o_o I hear filament hydration is a problem, so I'm not sure if this translates to already printed plastics ._.

Much less of a problem when it's already extruded

 

[Duality92]

I have one on the field that's been in use for months already. I'm planning to start printing custom waterblock tops for low profile use too

 

[Duality92]

I'll post a video of the installation of one that I'll be sending shortly that I'll be testing on my 290X.

 

[ReezyJeezy]

did you post the video yet?

 

[Amathophobia]

Were you ever able to get the leaks figured out. I ran into a situation where this terminal would be a life saver.

 

[Amathophobia]

Were you ever able to get the leaks figured out. I ran into a situation where this terminal would be a life saver.

 

[cennis]

Didn't know this existed! Cool DIY.

 

[SFFMunkee]

Big ol' thread-dig here, but anyone seen something similar? Not sure @Duality92 is still on SFFn, last seen June 2021

I'm looking to reduce the height of my EK 6800 block, and haven't found a solution yet, short of getting something made.

 

[cennis]

Big ol' thread-dig here, but anyone seen something similar? Not sure @Duality92 is still on SFFn, last seen June 2021

I'm looking to reduce the height of my EK 6800 block, and haven't found a solution yet, short of getting something made.

You can buy a similar one on taobao. Pmed

 

[SFFMunkee]

You can buy a similar one on taobao. Pmed

Thanks mate, appreciate it!

It'll have to wait a bit (thanks to my lack of 'toy' funds), but really glad to know there's something available

 

[Jeeva]

I've been having a similar issue for a 3080! Had a scour of Taobao, but no luck finding any low profile terminals. Is there something specific I should look for?

I guess it's possible that this barrow terminal would do the job, or I could just get the Barrow block instead of the EK I was looking at.

 

[EternalHell]

Thanks mate, appreciate it!

It'll have to wait a bit (thanks to my lack of 'toy' funds), but really glad to know there's something available

Did you end up pulling the trigger?

I'm am running a ekwb tuff 6900xt and if I can get my hands on one of those terminal a dual rad build in the formd t1 would be viable!!

Please pm me! Haha

 

[SFFMunkee]

Did you end up pulling the trigger?

I'm am running a ekwb tuff 6900xt and if I can get my hands on one of those terminal a dual rad build in the formd t1 would be viable!!

Please pm me! Haha

I ended up bricking my card, shortly after that, when I removed the ARGB part of the waterblock, without realising it also formed a spacer.