Recent content by Da_Korn

  1. Da_Korn

    Log 4L Custom STX Case Deskmini X300 with RTX GPU (brickless) 3d printed

    --> Thanks for your advice. I´d probably go for the soldering solution. Oh yes. I forgot to make Radiuses in the Design. The final one will get some. Also less rework after printing is done. Here´s a Picture form the MB-Side. Think it looks quite clean so far. Cable Management looks...
  2. Da_Korn

    Log 4L Custom STX Case Deskmini X300 with RTX GPU (brickless) 3d printed

    Thanks for all the Feedback. I did some changes to the rear, designed and printed the bottom Panels and reworked all the cabling. rear panel, printed with the Infill technique mentioned above: AC Power: 12v out: More Cables: Bottom Panel. I´m not quite happy with the current design...
  3. Da_Korn

    Log 4L Custom STX Case Deskmini X300 with RTX GPU (brickless) 3d printed

    that would be a great solution. But as long as it works without the load switch I´ll keep it as it is, maybe add it later. Those XT60s were just added for Testing purposes, I had them lying around. Yes they are really bulky. Yes, XT30s are a better altenative, or maybe connect everything...
  4. Da_Korn

    Log 4L Custom STX Case Deskmini X300 with RTX GPU (brickless) 3d printed

    Thanks, I appreciate it. I used the proprietary PSU, because the system only needs 12v and thats the highest power unit I could find in that formfactor. I know that 500w are way too much for the X300 and the rtx2070 but I wanted some Headroom for bigger hardware in the Future. But, I also chose...
  5. Da_Korn

    Log 4L Custom STX Case Deskmini X300 with RTX GPU (brickless) 3d printed

    Hello STX Fans, I wanted to post an Idea, thats been swirling around in my head for a while. Another small form factor Case, based on the Deskmini. I don´t know if thats a just a build LOG or a Concept. My plan was to implement an ITX GPU to the x300 Board and the System should also be...
  6. Da_Korn

    Log ~2L 11th Gen i5 & Turing dGPU

    Very very cool PC you built there. I like those 12v Nuc and STX etc. builds, where Space efficiency is important. Your Build gives me inspiration for some projects and ideas.
  7. Da_Korn

    Concept 92mm Distro Plate with DDC Pump and Reservoir

    Thanks. A D5 version is possible. The Case is the Metalfish S5. 12L in volume, kinda like the Ncase M1, but you can fit mATX motherboards in it.
  8. Da_Korn

    Concept 92mm Distro Plate with DDC Pump and Reservoir

    Hello people, I´ve got an Update of the custom mini Distro Plate. I managed to make the design real, so me and a colleague cnc milled it out of some acrylic panels. fisrt picture after mounting both plates: I used 1,8mm NBR rubber O-ring, which I cut and glued the right length together. First...
  9. Da_Korn

    Concept 92mm Distro Plate with DDC Pump and Reservoir

    thanks man. Absolutely right. I designed it for Case applications with no side radiator. For aesthetic reasons. I want to see my components and use a Pump distro that also looks good. If you have a side mounted rad, I think you dont care about how the CPU cooler or RAM RGB looks. In my case I´m...
  10. Da_Korn

    Concept 92mm Distro Plate with DDC Pump and Reservoir

    Hello SFF Commmunity. I always wanted to have a Distro Plate like EK´s Quantum FLT 120 but smaller, since the 120mm version wont fit at the back of an Ncase M1, NR200, etc. So I designed one, I actually have three different 3D models for this, but the last one I put in the most work and time...
  11. Da_Korn

    7L watercooled SFF Case (Dual 92mm radiator)

    finished build: next to a Sharkoon TG5 Tower recently my PSU has blown up and it killed my Vega56 plus my x570i too.
  12. Da_Korn

    Discussion Case Layout ideas

    Hello SFF enthusiasts. over the last couple of months I did several Case layouts. I started every idea but only till the Rough layout. Then I stopped because I dont know how to design the outside enclousure. Here I want to share them. Please share your thoughts and give me feedback or...
  13. Da_Korn

    Log My K39/Velka 3 inspired custom SFF case design. (noob design)

    Can you make a drawing of your idea? Do you know the J-Hack pure MK2? its also a very small case with just an itx MB and LP GPU, but with external Powerbrick.
  14. Da_Korn

    Log My K39/Velka 3 inspired custom SFF case design. (noob design)

    hi. I´ve tried to recreate your idea in Fusion360. just the Basic Panels. Nothing Special: if you wanna learn fusion360 we could work on Cases together.
  15. Da_Korn

    Log My K39/Velka 3 inspired custom SFF case design. (noob design)

    Great Case. I also started my first designs in Tinkercad, but I switched to Fusion360 (The non Commercial version is for Free), Because you can do thing more precisely. Here´s my 4.1L case with space for flex PSU and Low Profile GPU. Currently I have not made a specific Threat about that case...