Cooling Dynatron K129?

[HeroXLazer]

Do you think a Dynatron K129 without a fan strapped on would be enough for an i7 8700K?

 

[Kmpkt]

Heatsink only? Absolutely not. The heatsink is actually quite slim and the fins are very close together to take advantage of the high rate of airflow that the blower fan provides.

 

[HeroXLazer]

Heatsink only? Absolutely not. The heatsink is actually quite slim and the fins are very close together to take advantage of the high rate of airflow that the blower fan provides.

How much airflow in a fan do you think I need? Also, what do you think is the smallest cooler I can use for this? I'm trying to find something under 35mm.

 

[Kmpkt]

I think you're going to have a mighty hard time finding anything that can cool an 8700K comfortably at 35mm or less. The L9i handles the 7700K at stock frequencies, but not with a lot of wiggle room. Considering how much more heat the 8700K looks to put off, I'm not sure any of the current crop can handle that. I am about half way through testing virtually all of the <50mm coolers on the market and most of them have significant issues cooling a stressed 7700K.

 

[HeroXLazer]

I think you're going to have a mighty hard time finding anything that can cool an 8700K comfortably at 35mm or less. The L9i handles the 7700K at stock frequencies, but not with a lot of wiggle room. Considering how much more heat the 8700K looks to put off, I'm not sure any of the current crop can handle that. I am about half way through testing virtually all of the <50mm coolers on the market and most of them have significant issues cooling a stressed 7700K.

Are there any ways I can transfer the heat to a little space next to my motherboard (90ishmm x 90ishmm)?

 

[SeñorDonut]

Are there any ways I can transfer the heat to a little space next to my motherboard (90ishmm x 90ishmm?

80mm watercooler? 90x90-ish mm heatsink with long heatpipes?

 

[HeroXLazer]

80mm watercooler? 90x90-ish mm heatsink with long heatpipes?

I only have 50ishmm above the open space... There are no fan and radiator combos that are thin.

 

[SeñorDonut]

I only have 50ishmm above the open space... There are no fan and radiator combos that are thin.

Get a thinner fan or use a small-ish heatsink and some long heatpipes?

 

[AleksandarK]

Can you give us a picture of that space with correct measurements, so we can work out a solution?

A lot of ideas come to my mind, but i need to see how the given space looks, in order to recommend something.

 

[HeroXLazer]

M-ITX With BIfurcation
107.7118mm from side of Motherboard to Case Edge
37.98mm from side of Motherboard GPU Edge
51.1048mm from bottom of case to PSU Bottom

 

[msystems]

I have that heatsink. Its pretty worthless trying to cool my 6700k without airflow. If I had to guess, it's only handling like 15 watts. The fins are just too close together.
If air could be forced down the length of the fins I believe it could make a good cooler.

 

[HeroXLazer]

I figured it out. I didn't know how I didn't think of this earlier. I'm going to turn a triple 40mm radiator sideways.

 

[Kmpkt]

That sounds like an awesome idea. Post build pics please.

 

[HeroXLazer]

That sounds like an awesome idea. Post build pics please.

I'm still in the design phase... But, I should have everything done by the time Volta comes out. BIFURCATION. I'm just wondering, how long has it been since you changed your name?

 

[Kmpkt]

Like a year or so?

 

[HeroXLazer]

Like a year or so?

Knowing me, probably. I tend to design stuff, and not make anything...

I was looking through my design, and I realized that I made the Flex ATX models 220mm, because I was looking at the longer units, but now that I can put two in, I realized that I have so much clearance above the extra space beside the motherboard...

Also, I'm just wondering, do you know what fan the FSP 500-FSPT has. I'm going to see if I can mod it depending on the airflow.

 

[Kmpkt]

Also, I'm just wondering, do you know what fan the FSP 500-FSPT has. I'm going to see if I can mod it depending on the airflow.

I don't actually have the unit anymore as I sent it to @iFreilicht months ago. Perhaps he can answer the question for you.

 

[iFreilicht]

Also, I'm just wondering, do you know what fan the FSP 500-FSPT has. I'm going to see if I can mod it depending on the airflow.

Perhaps he can answer the question for you.

I can indeed:

 

[HeroXLazer]

I can indeed:

Thank you.

Edit: I can't seem to find it on the internet. I can only find model numbers that are similar. What is the thickness for the fan?

 

[FoskcoRS5]

Thank you.

Edit: I can't seem to find it on the internet. I can only find model numbers that are similar. What is the thickness for the fan?

40mm X 40mm X 28mm

Found it on ebay but that's it.

What about the Noctua's? 8mm shorter.