Recent content by Navy8or

  1. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Alright fellas, I need some technical help. So I'm doing a custom loop in my sm570, and I chose to go with Alphacool's systems. Basically I have a GPU block/pump and a cpu block/pump in the same loop. Only problem is that my X570-I brilliantly only comes with two fan headers (one CPU fan and...
  2. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    You guys can also call them. I realize that may not be the best solution for people outside the U.S., but for those that are here, they are incredibly helpful over the phone.
  3. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    I’m not sure there will be enough space. You got about 2 in from the center spine to the outside of the case and another 2 in from the end of a 10.5 in GPU to the front wall of the case. That reservoir is over 3 inches wide so idk how you’d get it mounted in there without some serious...
  4. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    That makes much more sense. So once I get the pump I now have the cpu fan header available to use. So I could feasibly set up the three 120mm fans off the sys header and the 92mm fan off the cpu header right? Where does the pump connect to? I don’t see a pump header anywhere in the board...
  5. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Looks exactly like what I’m going for! Did you just use a fan splitter and connect all your fans to the one header? I think thought there were two headers on the Gigabyte but one of them must be used for the chipset fan. As of now I’m going to see if the 240 can cool both the cpu and gpu, but...
  6. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Well I’m definitely an idiot. I set all the Sliger stuff to the side and forgot about it... the screws were in there. The Gigabyte board is a tough squeeze, but it makes it in there. Only slightly annoying thing is that the board and I/O shield are upside down given that the board mounts to...
  7. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Thanks for the advice count! I learned quickly that the mobo wouldn’t go in if I had the PSU installed. I’m waiting on an AIO but was planning on using the supplied wraith prism until then and leaving the side panel off. That was a disaster to say the least. It comes with a mounting system...
  8. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Okay thank you! I saw #6-32 online as well but also saw some others, so I appreciate the clarification! Also, these cases are tiny!!! Definitely picked a tough one for my first build!
  9. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Do cases or motherboards usually come with mounting screws for the motherboard? I got the x570-I from Gigabyte and it didn’t come with any screws from what I can see. Does anybody know the standard size screw I should get to mount it? Also, if anyone else has the gigabyte x570-I, does the M.2...
  10. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    @KSliger I've asked this before but didn't get a response. I know you're busy, but hopefully you can get back to me. With the 570 you state that 240 rads need to be 130mm max width to fit. From the pictures I'm seeing it looks like there may still be a bit of room between the rad and the...
  11. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Just email Sliger and get a refund. They are super friendly, so I'm sure you'll have no problems. Seriously though, I think everyone here would recommend to you that you no longer purchase anything on release date. It is a well known fact that every first-release will have a learning curve...
  12. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Is that the 570 or 580? I really want to put a HLabs rad in my 570 but they are 3 mm too wide. Do you think hanging the rad from the fans would allow for the rad to be 1.5 mm wider or each side? @KSliger can you weigh in on this?
  13. N

    Production Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    I ordered as soon as they went online. Got my tracking information yesterday. Expected arrival date is 29 July if that helps anyone with timing considerations. I believe there were options for faster shipping, but I just went normal.