Recent content by ermac318

  1. E

    Prototyping SV590 and SV540 - Vertical SFF Cases!

    I would think if you weren't going water at all - you would want the SV540, no? Why get the SV590 if not for the 360mm radiator?
  2. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    On you reservoir - is that a fill port at the top and a drain at the bottom? Totally Amazing, BTW
  3. E

    Prototyping SV590 and SV540 - Vertical SFF Cases!

    I prefer the consistent vent pattern of the SV540.
  4. E

    Prototyping DICE CASES - FLOW : expandable SFF case for watercooling enthusiast (built in distroplate)

    Confirming the Distro Plate is for D5 pump in this version? I don't see a choice to select one or the other
  5. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    I'm not Sliger so don't take my word as gospel. He was specifically responding to my question about the Cerberus with ITX board shifted down (I think, at least that's what I thought I was asking) because that would give you 280mm support in the top and bottom (like people were asking for in the...
  6. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    He answered this in the affirmative on the last page. I don't think that it would be smaller, it's that the innards would be shifted downwards in such a way that an ITX board could be mounted with space for radiators in the top and the bottom.
  7. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Are you considering moving forward with the ITX version of the Cerberus to allow for better radiator support? That would be a banger.
  8. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Agree 100% on this. mATX is a mostly dead form factor, and unless 3rd gen Threadripper brings it back in a major way, the Cerberus will become less and less useful over mITX cases that provide better flexibility. Allowing a shift downwards to accommodate 280mm rads on both the top and bottom...
  9. E

    Prototyping SV590 and SV540 - Vertical SFF Cases!

    What does it look like with a video card inside? Is there space for a 2 or 3 slot card? It looks like 2 but just wanted to be sure...
  10. E

    Completed 12L Cube style case with 140mm EK-MLC Phoenix support

    You may want to watch OptimumTech's review of the EK Meltemi 38mm thick fans. He found them worse than the Noctua A12x25 across the board. I know you're running a 140mm rad here but I can't imagine them being worlds ahead to justify their thickness.
  11. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Radiators aren't 120mm x 120mm square, because one side will be longer due to the U-bend and the other side requires space for the inlet/outlet ports. Because of the width of the case, you must orient the radiator such that the hoses come out on opposite sides of the spine. This means most AIO...
  12. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    I don't mean to be a pest asking for this, but any kind of guidance on custom loops would be appreciated. Several months ago you stated you were going to provide some examples and so forth, and in the intervening time I've seen a few custom loops posted on here, but they've all been enormously...
  13. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    Almost certainly not enough room for that. I think you can fit a ~28-30mm rad + 15mm fan, OR A 20mm Rad (think XSPC TX120) + 25mm fan.
  14. E

    Production The Sliger SM550/560/570/580 (2 and 3 slot riser layouts, with air and liquid cooling variants)

    The problem I think with a 140mm rad in the bottom is I don't think you will be able to fit a 140mm fan on top of a 140mm rad. You can do this with the 120mm rad/fan because the adapter offsets it towards the front of the case, avoiding the spine and the PCIe bracket. But while you have ~28mm of...