Recent content by cennis

  1. C

    Production Aquanaut Combo/Extreme [Available] - Ultra Low Profile CPU Block & Pump Mount Combo

    Can you run Heaven loop with the new aquanaut? Port Royale is basically idle CPU loads where Heaven uses more CPU, so that accounts for a large part of the 20c decrease.
  2. C

    Funding SLATE-CASE AQ >>Push for Production!!<<< New Website for Waitlist and Progress Updates!!

    Thank you! The card's power plugs are actually recessed down, lower than the top edge of the PCB (if you refer to my photo in the T1). This is different than the XC3 card that sffbuilds posted which goes right up to the top edge of the PCB. But of course, in an optimized case like this, custom...
  3. C

    Funding SLATE-CASE AQ >>Push for Production!!<<< New Website for Waitlist and Progress Updates!!

    Any options to have both the glass/perforated panels? or one of each? Planning a dual 280mm rad set up so I might need at least one perforated panel right?
  4. C

    Funding SLATE-CASE AQ >>Push for Production!!<<< New Website for Waitlist and Progress Updates!!

    I have the EK Strix 3080/3090 water block, it is 154mm tall, and plus another 12-13mm for the PCI-E finger, brings the total height to be 166mm+. It looks like it could fit given how far to the right the GPU riser is mounted, but would like to confirm if this is would fit in 2x 280mm rad config...
  5. C

    Funding SLATE-CASE AQ >>Push for Production!!<<< New Website for Waitlist and Progress Updates!!

    Whats the maximum height GPU that can be used with dual 280 rads + 3 thick fans and 1 slim? I am asking because there are a few models such as Strix and FTW3 that are about 140mm tall + 25mm extra for the Waterblock terminal which sticks out above it.
  6. C

    Production FormD T1 Classic (READ FIRST POST)

    Just wanted to share my build where it all started. Been a crazy journey but I made it before the V1.5 release.
  7. C

    Prototype Steck v2.0 - Minimalist, Stackable, Sandwich Style SFF Case. Up to 3x slot GPU [325mm (L)]

    Does this mean the tophat will support 280mm radiators?
  8. C

    SKYREACH 4 MINI (S4M)

    Is there anywhere that lists the updates made in R5 and R6?
  9. C

    Production FormD T1 Classic (READ FIRST POST)

    Can Canada be considered part of the US?
  10. C

    Log Dual 280GTS Meshy-boi (5900X, 3080 FE, 14.6L) build log

    If you are in need of a few more mm off the thickness of the fan + rad, you can sand/grind the mounting corners of each fan such that the fan motor is recessed into the radiator shroud. This could gain you another 3-6mm depending on how far you want to go and how deep the radiator shroud is...
  11. C

    Concept LUX - 11.3L Focus on premium design and liquid cooling - Slim Console Style

    Koolance low profile 90, barrow/bykski non rotary 90, alphacool TPV 90 rotary. All are around 20mm high. Most CPU blocks are about 20mm as well. So the bare minimum is 40mm-45mm. To fit a ddc pump block combo you need 45mm-50mm depending in which block model/heatsink. T1 has 50mm in 3-slot mode...
  12. C

    Production Winter One -- 15.6L SFF case, 3090 Support, 3-slot GPUs, dual 280mm radiators, CFD Optimized Design

    What is the maximum GPU height (i.e. from PCI-E finger to the highest point of the terminal manifold) with 30mm rad + 25mm fan mounted on the top? Would the 3080 FTW3 work? Seems to be ~165mm tall with the waterblock.
  13. C

    Concept LUX - 11.3L Focus on premium design and liquid cooling - Slim Console Style

    Interesting layout and great design. 140mm max GPU height might not be sufficient for most water blocks due to the top-mounted terminal
  14. C

    Production No more sandwich. W19. Up to 360AIO and custom loop. Up to full size 3-slot gpu. DDC pump. Ready for uncompromise watercooled in 10.5L console case.

    Interested! Is the W19 meant to support watercooling the GPU? Any renders? W19 GPU size up to 330x130x63 (in 240rad mode or with air cooling) or 217x130x63 (in 360rad mode at full power) 130mm height is not sufficient to water-cool even 3080 FE due to the terminal at the top which adds ~25mm...