Recent content by BananaOoyoo

  1. B

    Production FormD T1 Classic (READ FIRST POST)

    Thanks! Right now, I’m planning on air cooling the system. Definitely going to replace the fan on the Scythe Big Shuriken 2 Rev.B at some point (if not now, then when the A12 is released). I guess I can always stick with what I have and re-evaluate if thermals are awful.
  2. B

    Production FormD T1 Classic (READ FIRST POST)

    What are the best case fans for the T1? Right now, I have 2 Noctua NF-F12s (case) and a Scythe Slipstream Slim (CPU) from my existing build. I can upgrade to a 25mm fan for my CPU because of the higher clearances on the T1, and I'm also looking at potentially swapping out the F12s. I was...
  3. B

    Production FormD T1 Classic (READ FIRST POST)

    Shipping was $20 to Korea. But shipping isn’t the only factor involved with costs - as far as I know, there shouldn’t be an import fee for the T1 shipped to the US, whereas I’ll be hit with one here. In terms of overall cost, you’re better off shipping to the US (which is why I asked in the...
  4. B

    Production FormD T1 Classic (READ FIRST POST)

    Site loaded at 9:01 for me, and I just chose my case (black w/ riser) and entered my payment information. Not sure if having the payment information saved is even necessary - probably took less than a minute regardless.
  5. B

    Production FormD T1 Classic (READ FIRST POST)

    I ordered from Korea - what exactly is the question here? Not sure how much shipping was to the US, but KR shipping is probably cheaper.
  6. B

    Production FormD T1 Classic (READ FIRST POST)

    The all-silver looks fantastic too. Decisions decisions
  7. B

    Production FormD T1 Classic (READ FIRST POST)

    Think I’ll be looking at the two-tone or cerakote white! They look great
  8. B

    Production FormD T1 Classic (READ FIRST POST)

    I’m having a similar concern with GPU fit, though with height vs. width. If it isn’t a clean fit as-is, I wonder if there will be room to tinker with it, whether it’s 3D printing a new GPU bracket or (in my case), removing the LED strip on a FTW3.
  9. B

    Discussion Looking for a new case

    Perfect. If I go the S1 route, I’ll do the medium tophat, pick up a ~15mm fan for the CPU, then figure out what to do with the remaining three. (Slipstream & 2x NF-F12, so one under the PSU and two in the tophat)
  10. B

    Production FormD T1 Classic (READ FIRST POST)

    Yeah, I saw that it's 140mm card height to strut and 151mm to panel. If it's just the PCIe connectors that cause problems, then I could look at low profile options, but I'm not sure if the GPU itself can be crammed in there. (Maybe with minimal modifications?)
  11. B

    Production FormD T1 Classic (READ FIRST POST)

    Hi! Will the T1 fit a 1080Ti FTW3? There were a couple posts on it earlier, but I couldn't find a conclusion. The dimensions are: 299.72mm x 142.69mm x dual slot.
  12. B

    Discussion Looking for a new case

    The S1 in its base configuration only has room for 1 case fan, right? So I could go for either the small tophat for GPU cables, or medium tophat for cables & the second fan. Did you end up replacing the stock fan for the BS2? It looks like there's enough clearance for a 15mm fan, so I could...
  13. B

    Discussion Looking for a new case

    Hey everyone, My brother was interested in downsizing his pc and specifically interested in the Node 202 I'm currently using, so I am considering transplanting my system in a new SFF case. My current build is below: CPU: Intel Core i7-8700K 3.7 GHz 6-Core Processor CPU Cooler: Scythe BIG...
  14. B

    Hello from Seoul!

    Hey guys, I found this forum today just looking at new cases for my upcoming build/transplant. My first SFF build (and first build in general) was ~2.5 years ago when I decided I wanted a gaming-capable pc that would also fit in a backpack. My younger brother recently got interested in...