Recent content by Wyd4

  1. Wyd4

    Production Meshlicious - 14.5L Vertical, 280AIO mainstream case

    Wouldn’t be the first time I built a pc in a cardboard box
  2. Wyd4

    FormD-T1 Vertical orientation base

    ditto
  3. Wyd4

    FormD-T1 Vertical orientation base

    Did this idea ever progress? I think it had some merit. I was keen to see just a simple basic “stand” to change the orientation of the case. Nothing more.
  4. Wyd4

    FormD-T1 Vertical orientation base

    In summer have the "top" of the case facing the back of the desk. In winter turn it around and save on heating :P
  5. Wyd4

    FormD-T1 Vertical orientation base

    Personally I dont even need front IO. Just somewhere to mount the power button on the back with the cable outlet and I am happy :)
  6. Wyd4

    FormD-T1 Vertical orientation base

    I would be interested in this as is right now haa
  7. Wyd4

    FormD-T1 Vertical orientation base

    I would be interested in this. (Currently lucky enough to have the formD on my desk. The footprint is tiny but this would be ideal. The footprint would be literally tiny. it would look super clean too.
  8. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    Does not ship to Australia :’(
  9. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    Just depends on your motherboard and ram height really. However these aren't really case considerations.
  10. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    I am using the x570i gigabyte board. Unfortunately the m.2/chipset heatsink and the IO shroud is problematic in either direction. Basically with my EK 90 degree fittings on the block, it either hits my rad/fan, io shroud, m.2/chipset heatsink or ram, regardless of which way I point it. @fabio...
  11. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    When I looked, and I will look again now as I am paranoid after reading your post, the right angle fittings that come with the LT240/120 are G1/4, however they are a right angle compression fitting, so cannot put a normal compression fitting on the alphacool 90 degree one. For me, with the...
  12. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    Yeah I tried that (also here in Australia and cannot get 8/11mm cooling hose. Homebrew yes but I haven't been game haha. My old man is a mechanic and I have raided his shed. I can either get correct inside and outside diameter but the hose is very stiff and doesn't feel like it would end well...
  13. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    Yeah it all seems like a pain to be restricted for choice. Almost thinking about just getting a ek cpu block and a ddc pump and being done with it. Can only get the ek pump top version of the ddc over here so hoping it will fit. Will measure it up tomorrow morning. I reckon it’s gonna be tight.
  14. Wyd4

    Production FormD T1 Classic (V1.0 and V1.1) READ FIRST POST

    Bit of an odd question, or a specific one I guess. Has anyone had any luck mounting the LT240 cpu block on a Gigabyte x570i motherboard? I have currently got ek fittings on my LT block and it will not mount due to the chipset/m.2 heatsink. Trying to get some of the stock diameter tubing so I can...