Recent content by PKAWA

  1. P

    Production FormD T1 Classic (READ FIRST POST)

    Does anybody know the screw size for the Asus x570 motherboard cooler backplate? The screws that should have come with my chinese waterblock are missing making it impossible to mount it. I suspect it's almost m3 but not exactly. Edit: It's 6-32 x35mm. The only screw that you can't buy...
  2. P

    Production FormD T1 Classic (READ FIRST POST)

    Yes me too. I would like to buy a front panel in silver, and a center beam that has the cut out for the gpu. My current T1 does not have this and it interferes with my 3080 power cables.
  3. P

    Production FormD T1 Classic (READ FIRST POST)

    Awesome! Happy I went with the black Gmmk pro order instead of the silver one now.
  4. P

    Production FormD T1 Classic (READ FIRST POST)

    Will you do duo tone black/ silver again? Would like to order that
  5. P

    Production FormD T1 Classic (READ FIRST POST)

    I'm not using either, I have a coolworld 240 25mm with fillport in the back which I've connected to the back of the case so I'm not willing to change it :) Besides, it's better than the Alphacool rad. I've had that before this one. Now I'm going to use it in 3 slim fan mode, but would have...
  6. P

    Production FormD T1 Classic (READ FIRST POST)

    Yes I'd also prefer 50mm below the motherboard for 25mm rad with 25mm chromax fans.
  7. P

    Production FormD T1 Classic (READ FIRST POST)

    Thank you for the info! from what you are telling me now I feel I can make a good choice and that it won't have any added value for me personally to wait for the evo. I don't want to expand my case over the size of the Formd T1.1, I just want it to be more flexible and that is what the 1.2 is...
  8. P

    Production FormD T1 Classic (READ FIRST POST)

    The only thing that kind of irks me is that there's still no parts available for the T1 while it's out for quite a while now. Sure I understand that production lines are being a nuisance and the total output of T1 cases is still too low to sell them. But I'm a little worried that parts that are...
  9. P

    Production FormD T1 Classic (READ FIRST POST)

    I'm in the same boat and agree with you and would also like to know more about the evo project to make an informed choice.
  10. P

    Production FormD T1 Classic (READ FIRST POST)

    No, I have been asking for parts numerous times, and they are not selling them (yet) Hoping that they will at some point, but actually not sure anymore since there's two new cases on the horizon now.
  11. P

    Production FormD T1 Classic (READ FIRST POST)

    Okay, and from what I can now tell the 1.2 case would solve my problems in 2.75 slot mode but I know I have a 1.1 case and I'm stuck with this problem. Just figured this out myself after you asked for pictures because I have been struggling with this card in my case. Is there a chance support...
  12. P

    Production FormD T1 Classic (READ FIRST POST)

    What I mean it's that my center strut has no cut outs for the gpu cables so it doesn't fit in my case properly. The last picture I added is not from my case but to show the difference with my case with a similar gpu. Dont mind the gpu cables, they will be shortened yet. Also, a few more mm...
  13. P

    Production FormD T1 Classic (READ FIRST POST)

    Does V1.2 have better gpu clearance to the motherboard? Currently the gpu 3080tuf is too close to the Asus x570-i and so it is angled downwards and sideways putting a lot of strain on the card. 5mm offset faway from the motherboard would be ideal, but in the current case this would result in the...
  14. P

    Production FormD T1 Classic (READ FIRST POST)

    Thanks for getting back to me, didn't know anybody had actually already used it in a build. From what I can find on the internet it should work. The black one looks good in your build so I ordered one as well.
  15. P

    Production FormD T1 Classic (READ FIRST POST)

    I have a quadro aquacomputer and it has the 5pin usb connector. The problem is that my only usb port on the motherboard is taken by my silverstone remote control, so was wondering if anybody has the pin out to be able to cut of the 5 pin and connect it to the usb 3.2 header with a standard 3.2...