Recent content by makiasd

  1. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Could you also update the original post with the specs for Batch 3? I think the height was raised by 8mm at some point so I think the CPU coolers up to 42mm are supported?
  2. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Will Batch 3 be able to fit 7mm SSDs underneath the GPU?
  3. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Out of curiosity, whats the +5mm in width for?
  4. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Could the GPU be raised by 2mm to make space for normal 7mm SSDs?
  5. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Personally i'm holding off on ordering until its confirmed that SSDs can fit under the GPU
  6. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Any update on this?
  7. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Maybe with the extra 3mm you can now fit 2 SSDs under the GPU? Wouldn't be any thinner but possibly less wide because of the pcie extender needing less space to bend.
  8. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    By my calculation up to 2 SSDs could fit side-by-side underneath the GPU: +52mm outer dimensions -03mm case thickness (1.5mmx2) -37mm GPU thickness 12mm remaining Almost all SSDs are 7mm thick nowadays
  9. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    How heavy is the case?
  10. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Two questions: Could the DC input port be moved down closer to the bottom panel? Could the power button be relocated to the rear panel above/under the DC input port?
  11. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Would a drilled-hole venting design similar to the DAN A4-SFX be possible?
  12. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Would be great if there was the option to customize the bottom panel to have 100x100 VESA mounting holes:
  13. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    In the past CustomMOD has offered multiple vent patterns to choose from and has been very flexible with any other customizations. Hopefully they have the same flexibility here too.
  14. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    Judging from the sketch if the GPU was raised a 7mm SSD might just be able to fit below. Wonder how the temps would be though. Edit: Beautiful C cases btw
  15. makiasd

    Production cases: SLM1m/ SLM1 4L/ SLM2 5.7L by Custom_MOD

    What advantage does routing the PCI-E under the motherboard have vs routing it under the GPU? I'm concerned about poor ventilation to the M.2 slot on the back of the motherboard.
See more