Recent content by DrAwesome95

  1. D

    Part Low profile angled c13 connectors

    They both still use thin guage wires - they look about 20 guage which is pretty close to being a fire hazard. Looking to push peaks of 500W through it (RX 5700XT, R9 3900X) Also I live in Australia where power laws are quite strict - so if anything happens I am totally screwed haha. I found one...
  2. D

    Part Low profile angled c13 connectors

    @Necere sorry to zombie post - but do you still sell these cables - I cannot find them on SFFLAB
  3. D

    Production Velka series cases for ultra compact and portable desktops

    Is there a changelog for the Velka 5 Rev 1.1? Also - will a 200mm PCIe riser work?
  4. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    The Vega Nano ran notoriously warm - and was infamous for coil whine. Lets hope Navi is done better
  5. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Dont mean to sound like a pessimist, but RTX dosent really intrest me - for the last 2.5 gens the x70 series has been the only enthusiast level card available. And what I mean is that more people will consider buying into a case that gives options rather than pigeon-hole into a single build. In...
  6. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Yes, what I mean is enabling potential users to adapt an existing GPU to a compatible form factor. The specific example I used is the Sapphire Pulse Vega 56 (triple fan) which actually had a 'Nano' PCB. Adapting that to a single fan would lower the cooling potential somewhat, but for majority of...
  7. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Great to see everyone trying to make another production run happen - I think the biggest drawback with the MI-6 is the fact it will only support 2 slot, half length GPUs (upto 200mm). The way the industry is going - seems like we're only getting super chunky overbuilt monstrosities for the...
  8. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    What a time to be alive
  9. D

    DAN C4-SFX - old

    Awesome to hear, by far the sleekest solution to a 240mm radiator SFF case. Sadly industry seems to be leaving SFF behind, again - please can you look at a 2.2 slot clearance for GPUs (like in the Ncase rev 6). Also, you probably will go through SFF Lab again, would be awesome if you broke up...
  10. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    The fastest card currently available to consumers (2080ti) barely saturated 8 lanes at Gen 3 speeds. Thankfully it will be a while before that even becomes an issue. Besides gen 4 ssds, I don't think PCIe Gen 4 is more than a gimmick.
  11. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    We had a debate on here earlier on but fingers crossed for a 5700/XT card less than 200mm in length. This time they didn't even have a Nano card to show off at launch like they did for Vega.
  12. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Can you PM me please?
  13. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Have had the same idea for a while, but it seems short of getting a custom cooler/ strapping on an AIO, there isn't much hope. At that point, its a massive leap to take financially, and I'm too chicken haha. I looked into buying a dead Aero card and fitting the cooler onto the Vega, but of...
  14. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    I'll buy your old one if you can get it to Australia :) Problem solved .
  15. D

    Completed The MI-6 Microtower Case: Performance in 6.7L

    Get scratching boys!