Recent content by draic

  1. D

    NCASE M1 V6 GPU Compatibility List

    too wide. The terminal would extend too far (~9mm). Even without the plastic shroud it will not work unfortunatly. EKWB also offers a special edition block which has the terminal recessed slightly, but it is still too wide for the ncase. Sucks that AMD used a wider PCB even for the reference design.
  2. D

    DAN C4-SFX - Update 15.03.2021

    this is a slightly smaller NCASE with a Ghost S1 front. Compared to the original C4-SFX I am not really sold on this iteration. I do not see much sense in supporting two GPU orientations. This requires different ways to mount both GPU and PSU, while standard layout will have a lot of limitations...
  3. D

    NCASE M1 V6 info

    the only part that needs the CE certification is the cable. And getting CE for that shouldn't be a problem. I had my fair share with german customs in the past and also problem about stupid CE requirements. For example I had the issue that an included charger was also missing the CE cert. After...
  4. D

    List of Mini-ITX/DTX motherboards with a Key A header (for front panel USB C)

    Bottom rad is not possible, correct. No concern to me. After the picture I installed an m.2 to pcie riser to put a 10gig network card in the third slot, so I couldn't fit a rad down there anyways.
  5. D

    List of Mini-ITX/DTX motherboards with a Key A header (for front panel USB C)

    here you go: The M.2 board does not interfere with the fittins and there is enough room to take it out, with the fittins still in place You need to mod the AM4-brackets of the pump to fit the motherboard, but not much of a problem. The backplate of the motherboard intereferes with one of the...
  6. D

    List of Mini-ITX/DTX motherboards with a Key A header (for front panel USB C)

    I have that motherboard running a custom loop in my NCASE. Why do you assume that is not possible?
  7. D

    Crosshair VIII Impact + M1 v6 = High Chipset temp

    Thanks for the notice. I have just updated and now my system is quiet again.
  8. D

    NCASE M1 V6 info

    it fits the V6, but one of the clamps of older versions interferes with the backplate of the motherboard. If you have version 1 to 5, you can either: a) remove the backplate (but it has a heatpipe) b) clip the pin from the sidepanel and remove the clip c) drill a hole into the backplate for the...
  9. D

    NCASE M1 V6 info

    So the main issue is with having all the different options and items available in the store and supporting that, correct? Might it work better to do a preorder/groupbuy then instead? So not supporting these items on the shop for now, but people can order something like like the power cable or...
  10. D

    NCASE M1 V6 info

    and Taiwan Post is the only available option? Why not change the carrier then? Can we assume that this is a temporary problem and you will offer parts again in the future?
  11. D

    NCASE M1 V6 info

    so providing upgrade kits for the I/O for the older NCase versions is canceled? Why? When the v6 was announced, this was the first thing I wanted to know and the clear statement was, that there will be an I/O replacement for older versions. Now this is not going to happen? Then you shouldn't...
  12. D

    NCASE M1 V6 info

    FAQ Q: When can I order the M1 V6? A: Next availability is TBD (est. January)
  13. D

    List of Mini-ITX/DTX motherboards with a Key A header (for front panel USB C)

    do you mind adding some photos of your build? I wonder how much space the DTX form fills up room below the graphics card inside the ncase and how this might limit options down there.
  14. D

    NCASE M1 V6 info

    When will parts like the new I/O ports be available separately?