Recent content by chinyang

  1. C

    Production FormD T1 Classic (READ FIRST POST)

    that gunmetal gray looks really good very keen to see what the all silver looks like!
  2. C

    Production FormD T1 Classic (READ FIRST POST)

    no problem
  3. C

    Production FormD T1 Classic (READ FIRST POST)

    this does looks interesting because everything fits so tightly inside, barely any space between components and side panel
  4. C

    Production FormD T1 Classic (READ FIRST POST)

    Did u run your L12S fan as intake or exhaust? I find that if I run it as intake, with the same cpu temp around 55 c during gaming, fan speed is about 50-60% when using fan as intake and will increase to 70-80% when using as exhaust. Using fan as intake does heat up the case a lot even with a...
  5. C

    Production FormD T1 Classic (READ FIRST POST)

    I run my L12S as intake blowing towards mobo thinking it’s probably beneficial for vrm cooling (not that I really need it because I’m not overclocking and not using a very tdp processor).. but I’ve never done any stress testing. Not sure how the other components like chipset, m.2 SSD are doing...
  6. C

    Production FormD T1 Classic (READ FIRST POST)

    @Wahaha360 what is the function of these two highlighted in red? I think it is not in the new manual
  7. C

    Production FormD T1 Classic (READ FIRST POST)

    Actually it’s screwed in on one side only, I placed some pads to support the other side. Just to demo/show/try out that with a little bit of creativity, there’s no lack of storage options. Alternatively, that space should allow at least a couple or more 2.5 inch SSD
  8. C

    Production FormD T1 Classic (READ FIRST POST)

    Default: fan facing sidepanel, cables exit to bottom Better alternative: fan facing sidepanel, cables exit to top
  9. C

    Production FormD T1 Classic (READ FIRST POST)

    Looks like the turning the psu 180 degree is the way to go whether using a aio or not.. will help with both cable management & psu exhaust in this orientation If turning the psu 90 degree, the cables exiting is too close to mobo, might not be feasible unless using custom ultra short cables
  10. C

    Production FormD T1 Classic (READ FIRST POST)

    highlighted in yellow... one is for 2 slot card, the other 3 slot
  11. C

    Production FormD T1 Classic (READ FIRST POST)

    Exactly... i think i will remove the bottom screw on the SSD side, just to reduce the stress on the connectors once secured it with the GPU to the backplate, i would say overall it's rock solid this is the first sandwich layout case for me though, so i have no past experience how others perform
  12. C

    Production FormD T1 Classic (READ FIRST POST)

    Just for sharing... My build specs: intel skylake 6600 + noctua L12S gigabyte h170n-wifi zotac gtx 1070ti mini ram 16gb DDR4 2133mhz corsair sf600 platinum m.2 SSD x 1 2.5 inch SSD x 1 3.5 inch HDD x 1 (yes, i put it in, why not?) *Temporary system - problem with Ryzen 3600 system riser...
  13. C

    Production FormD T1 Classic (READ FIRST POST)

    i thought flipping the SFX psu feature was removed... (vivid memory it was stated that it is dropped in one the older post) Glad to know it's back! Might help A LOT to keep the cable mess from chocking the 120mm aio fan. Thought i'm just going for L12S, will test it out later if i have the time.
  14. C

    Production FormD T1 Classic (READ FIRST POST)

    Malaysia shipment in summary: Consignment arrived at Dongguan Express Processing Center until China customs release - 2 days China to Malaysia (air transport, including waiting time in airport) - 2 days Malaysia customs inspection - 1 day Shipped: 6 March Received: 11 March Malyasia delivery...