Reply to thread

Message

Looking at this thread, I was inspired for my next project.

To preface, there has only been ONE apple product I have liked. The Mac Pro trashcan. And it's obviously not up gradable (or down-gradable in my case (pun fully intended)). I wanted a HDPlex 160, STX Mobo, and half height, single slot cards. But when I did a partial model, I realized there was room for a dual slot. It'll be enclosed with 8.5" of 6.5" aluminum pipe- for the metric folks: 215.9mm tall and 165.1mm wide. It'll have a fan at the top, and 3d printed top and bottom vents. For now, some pictures of the model:

https://image.ibb.co/n1Axdz/Capture.png

https://image.ibb.co/bxpqyz/Capturef.png

https://image.ibb.co/mXrg5e/ewrewr.png

https://image.ibb.co/d3R3Jz/rthdr.png

https://image.ibb.co/n4LkWK/wedew.png

Thanks,
Windfall

<blockquote data-quote="Windfall" data-source="post: 108285" data-attributes="member: 4759">Looking at<a href="https://smallformfactor.net/forum/threads/the-trashcan-3d-printed.7164/"> this thread</a>, I was inspired for my next project. To preface, there has only been ONE apple product I have liked. The Mac Pro trashcan. And it's obviously not up gradable (or down-gradable in my case (pun fully intended)). I wanted a HDPlex 160, STX Mobo, and half height, single slot cards. But when I did a partial model, I realized there was room for a dual slot. It'll be enclosed with 8.5&quot; of 6.5&quot; aluminum pipe- for the metric folks: 215.9mm tall and 165.1mm wide. It'll have a fan at the top, and 3d printed top and bottom vents. For now, some pictures of the model:<a href="https://image.ibb.co/n1Axdz/Capture.png">https://image.ibb.co/n1Axdz/Capture.png</a><a href="https://image.ibb.co/bxpqyz/Capturef.png">https://image.ibb.co/bxpqyz/Capturef.png</a><a href="https://image.ibb.co/mXrg5e/ewrewr.png">https://image.ibb.co/mXrg5e/ewrewr.png</a><a href="https://image.ibb.co/d3R3Jz/rthdr.png">https://image.ibb.co/d3R3Jz/rthdr.png</a><a href="https://image.ibb.co/n4LkWK/wedew.png">https://image.ibb.co/n4LkWK/wedew.png</a>Thanks,Windfall</blockquote>

[QUOTE="Windfall, post: 108285, member: 4759"] Looking at[URL='https://smallformfactor.net/forum/threads/the-trashcan-3d-printed.7164/'] this thread[/URL], I was inspired for my next project. To preface, there has only been ONE apple product I have liked. The Mac Pro trashcan. And it's obviously not up gradable (or down-gradable in my case (pun fully intended)). I wanted a HDPlex 160, STX Mobo, and half height, single slot cards. But when I did a partial model, I realized there was room for a dual slot. It'll be enclosed with 8.5" of 6.5" aluminum pipe- for the metric folks: 215.9mm tall and 165.1mm wide. It'll have a fan at the top, and 3d printed top and bottom vents. For now, some pictures of the model: [URL]https://image.ibb.co/n1Axdz/Capture.png[/URL] [URL]https://image.ibb.co/bxpqyz/Capturef.png[/URL] [URL]https://image.ibb.co/mXrg5e/ewrewr.png[/URL] [URL]https://image.ibb.co/d3R3Jz/rthdr.png[/URL] [URL]https://image.ibb.co/n4LkWK/wedew.png[/URL] Thanks, Windfall [/QUOTE]

Verification