Is it there a solution ???

[stefan33]

Hello to everybody, I tell you what I'm looking for: I wery simple kind of case that I can't find...
I want to put inside:
Mini ITX board.
Power supply HD Plex Combo:
http://www.hd-plex.com/HDPLEX-160W-DC-ATX-Power-Supply-16V-24V-Wide-Range-Voltage-Input.html
http://www.hd-plex.com/HDPLEX-Internal-160W-AC-DC-Adapter-with-Active-PFC-and-19VDC-Output.html
I don't like the idea of external adapter...

1 or 2 2,5 SSD.
If it's possible better if I can fit one low profile one slot Graphic.
I'm looking for a very small case but with a good ventilation for CPU.

This could be perfect but there is no space for HD Plex and also I can't fit a low profile one slot Grapic card.

http://store.antec.com/isk-series/isk110-vesa.html

Something a little bit bigger...

 

[jtd871]

If you got creative and used a short GPU (fit the AC-DC unit in the GPU area if you can't shoehorn it into the PSU area), maybe the DAN A4 would work.

 

[Ceros_X]

https://smallformfactor.net/forum/threads/lone-industries-l4-less-is-more.901/unread

I think this is closest?

 

[jottwehh]

definitly not a full list, but pretty much the best you can get:
http://www.overclock.net/t/1300645/official-usff-sff-club

 

[aquelito]

This could be perfect but there is no space for HD Plex and also I can't fit a low profile one slot Grapic card.

http://store.antec.com/isk-series/isk110-vesa.html

I am currently working on that case If you go the thin mini-itx way, then you can fit a LP single slot 750 Ti and the AC-DC HDPLEX adapter.

 

[stefan33]

I am currently working on that case If you go the thin mini-itx way, then you can fit a LP single slot 750 Ti and the AC-DC HDPLEX adapter.

Inside the Antec with a normal ITX it's possible to fit this ???
http://www.hd-plex.com/HDPLEX-Internal-160W-AC-DC-Adapter-with-Active-PFC-and-19VDC-Output.html

How? Thank you.

 

[aquelito]

You could, but only with a thin mini itx motherboard.

 

[cleveland]

I am currently working on that case If you go the thin mini-itx way, then you can fit a LP single slot 750 Ti and the AC-DC HDPLEX adapter.

I'm working on that case too!
There are any buildlog pictures you can share?

 

[aquelito]

@cleveland not yet, no.

I based my build layout on a cooling hypothesis that I still have yet to verify.
If it clears, then I'll go ahead and finish my build with the ISK 110.

I modelized the case though ; I have to improve it a bit and I can upload it in the reference library.

 

[Sean Crees]

You can put all that inside a NFC S4 Mini, its 4.3L. It was originally designed to use an external power brick with a full height double width graphics card, but if you use a low profile graphics card you can fit the HDPLEX AC/DC adapter inside the case. A post on these forums was made about doing this: https://smallformfactor.net/forum/threads/nfc-s4-mini-77-orangulan-brickless-s4.812/

 

[cleveland]

@cleveland
I modelized the case though ; I have to improve it a bit and I can upload it in the reference library.

I'd thank you very much if could share it.

Also, my plan consists of a very clean build: F2A88XN +A10-7860K +NH-L9a +HDPlex 160w DC-ATX PSU. Lightweight, SFF mobile gaming rig. The very best of both worlds.

 

[aquelito]

I made almost the same build, except I had an A8 7600 instead of the A10.

When the TDP is set to 65W, the CPU tends to run a bit too hot with a small NH-L9a.

I would advise you to look for a lower CPU cooler (around 30 mm tops ; the Thermaltake Engine 27 could be useful here) and have a slim 120/140 mm fan cooling down the whole motherboard.

FYI, you should have around 50 mm clearance between the motherboard PCB and the top mesh panel.

 

[stefan33]

I made almost the same build, except I had an A8 7600 instead of the A10.

When the TDP is set to 65W, the CPU tends to run a bit too hot with a small NH-L9a.

I would advise you to look for a lower CPU cooler (around 30 mm tops ; the Thermaltake Engine 27 could be useful here) and have a slim 120/140 mm fan cooling down the whole motherboard.

FYI, you should have around 50 mm clearance between the motherboard PCB and the top mesh panel.

I have A10-7800 with this:

http://noctua.at/en/products/fan/nf-a9-pwm

Much more better...

 

[cleveland]

I made almost the same build, except I had an A8 7600 instead of the A10.

When the TDP is set to 65W, the CPU tends to run a bit too hot with a small NH-L9a.

I would advise you to look for a lower CPU cooler (around 30 mm tops ; the Thermaltake Engine 27 could be useful here) and have a slim 120/140 mm fan cooling down the whole motherboard.

FYI, you should have around 50 mm clearance between the motherboard PCB and the top mesh panel.

I was aiming at the 45w cTDP mode.

About the case, i guess it was built with some jury rigging in mind. The grill over the mobo has the perfect shape and size to fix a slim 120mm fan with small/slim zip ties.

 

[stefan33]

One question: For you it's possible to fit this:
http://www.hd-plex.com/HDPLEX-Internal-160W-AC-DC-Adapter-with-Active-PFC-and-19VDC-Output.html
here:
http://www.lc-power.com/en/product/gehaeuse/mini-itx/lc-1510mi/
This should be the same:
https://world.taobao.com/item/17659686312.htm?fromSite=main&spm=a312a.7728556.0.0.X1OXLW

I like to put the HDPPLEX next to the pci slot, on the left side of the motherboard...
What do you think?