You would not be a good surgeon! I sure do not want to be your patient.?
But think about all of the new and different configurations you'd get to try out. @fabio would probably figure out a way for you to have a third lung without taking up any more space, and your VO2 max would go through the roof. We'd be watching you set distance running and endurance records left and right.
Does anyone have any tips on how to get the FormD re-finished?
I ask as very early in the piece my mesh chewed out the front panel. I have since figured out how to get it in there with minimal contact with the front, but yeah I would like to have it repaired if possible. I could simply paint it but I want to keep it looking right.
Also for those interested here are 2 aio's in the FormD. I do not really recommend it as if you are going to this effort it would be much easier to run a 240 rad and custom loop. However due to circumstances surrounding my gpu choice I previously purchased the NZXT G12, so I thought I would try get it to fit in the FormD.
Cable management leaves a little to be desired as I have not cable tied anything yet as I am not sure whats coming next haha.
I ask as very early in the piece my mesh chewed out the front panel. I have since figured out how to get it in there with minimal contact with the front, but yeah I would like to have it repaired if possible. I could simply paint it but I want to keep it looking right.
Also for those interested here are 2 aio's in the FormD. I do not really recommend it as if you are going to this effort it would be much easier to run a 240 rad and custom loop. However due to circumstances surrounding my gpu choice I previously purchased the NZXT G12, so I thought I would try get it to fit in the FormD.
Cable management leaves a little to be desired as I have not cable tied anything yet as I am not sure whats coming next haha.
Kinda surprised that all fit, but with what Fabio has shown us, I think it’s possible to fit anything in this case now lol
You are not wrong. Fabio is a mad scientist.
I am looking for a gpu block thats compatible with my GPU then I will likely loop mine wiht a 240 rad. I have everything I need except a gpu block.
I've now changed the 240 AIO Compatibility Googlesheet to allow edits by everyone. I set the current part of the list to protected, but you can now add new AIOs, if you can think of some I didn't. The colors and the colums showing if it should fit or if it fit's only in 2 slot GPU mode are automated, based on the values entered in the same line.
to avoid people having to scroll up and look for the Link, you can access and edit the sheet by clicking here.
to avoid people having to scroll up and look for the Link, you can access and edit the sheet by clicking here.
I haven’t added anything to my useful links sheet in awhile, but is it okay if I link this in there for people?
@Wyd4 I'm not sure if you saw a previous post of mine?...
Have you had a look at AliExpress? Bykski and Barrow make coolers for vendor cards that don't match the reference layout. I have a 2080S Gaming OC that is reference layout except for an extra fan header which means the blocks from EK and others don't fit.
You have the Windforce 2080 Ti if I remember reading your previous posts?
US $121.0 |Bykski N RTX2080Ti X FR N RTX2080Ti X Water Block use for NVIDIA GeForce RTX 2080Ti/2080 Reference Founders Full Cover GPU Block|Fans & Cooling| - AliExpress
Smarter Shopping, Better Living! Aliexpress.coma.aliexpress.com
US $91.96 16% OFF|Barrow BS NVG2080T PA, LRC RGB v2 Full Cover Graphics Card Water Cooling Blocks, For Founder edition Nvidia RTX2080Ti/2080,|Fans & Cooling| - AliExpress
Smarter Shopping, Better Living! Aliexpress.com
Oh thanks man, I did miss that. I will take a look at those.
I know the EK will fit but I would need to snip the header and shave some off the power connector.
The other option is to wait to see what the 3000 series cards come out at price wise.
Which brand do you have experience with? Would rather buy one that someone else has had a good outcome from.
Neither, but I was going to go with a Barrow block for my 2080 Super Gaming OC (same problem - reference PCB, additional header). Mainly because Barrow offer a rotary terminal block to replace the included terminal. (@optimumtech used similar from EK on his EK block to get the side panel to fit on).
US $12.41 8% OFF|Barrow BSQT360 01, 360 Degree Rotating Bridge For Barrow GPU Block, With 90 Degree Change Direction|Fans & Cooling| - AliExpress
Smarter Shopping, Better Living! Aliexpress.com
www.aliexpress.com
There are a few posts on OCAU for Bykski blocks, and PLE Computers in Western Australia stock a range of Bykski products so the QA is probably passable
Neither, but I was going to go with a Barrow block for my 2080 Super Gaming OC (same problem - reference PCB, additional header). Mainly because Barrow offer a rotary terminal block to replace the included terminal. (@optimumtech used similar from EK on his EK block to get the side panel to fit on).
US $12.41 8% OFF|Barrow BSQT360 01, 360 Degree Rotating Bridge For Barrow GPU Block, With 90 Degree Change Direction|Fans & Cooling| - AliExpress
Smarter Shopping, Better Living! Aliexpress.com
There are a few posts on OCAU for Bykski blocks, and PLE Computers in Western Australia stock a range of Bykski products so the QA is probably passable
Thanks again!!!
Much appreciated!
That's awesome!my way to infuse water when using dclt
What fittings did you use?
Do you think you could make that fit in 3 slot mode or does it stick out too far?
The quick fix is a black sharpie. It isn’t the most elegant solution, but it does the trick for the little corner scratches that occur.
Even i didn't understand this guy talking, but the effort and how to he build T1 with that AIO try to surpass fabio build.. but now i want to see more from fabio..
--
Edit:
Parts from his build
FormD T1
Gigabyte X570i
AMD R9 3950x
AMD Radeon VII
Corsair 64gb (Probably)
PCIE 4.0 M2 1TB
EK-Velocity AMD CPU AM4
EK-Vector Radeon VII
EK WB Classic SE 240 & Noctua A12x15mm
EK 18W DDC & OCOOL 1U
--
CMIIW
Last edited:
two 90 and one 3 links. It could be possible when using t-junction, maybe.
sorry, foget about the screws of the pump. it will block the pipe, so the angle in the picture is the limit. if use the t-junction, u cannot rotate it.
in case you figure something out, I'd love to know as well
I used Birchwood Casey Aluminum Black Touch-up which is used to darken the exposed aluminum in black anodized guns. It darkened and minimized the scratches in my T1. I have not taken the time to apply multiple coats yet, but it apparently darkens more as you apply it multiple times. There are a couple of examples in YouTube.
Having said that, nothing will ever make it look like new again short of re-anodizing and somehow matching it with the rest of the finish or buying the parts if/when available in the future .
Amazon product
Amazon product
Last edited:
