Recent content by TSOF

  1. T

    Production FormD T1 Classic (READ FIRST POST)

    Just put in my new dual 8-pin to 12 pin Ampere PSU cables from DreamBigByRay. Got him to make them 20cm and it''s pretty much perfect for a flipped PSU - enough room to install easily, but not so much that it bunches. I've also put in the Linkup Pcie4.0 riser - 20cm. There's a little more cable...
  2. T

    Production FormD T1 Classic (READ FIRST POST)

    Nah was curious as to the thermal impact a while ago, and can’t be bothered making new cables to turn it around! 😆
  3. T

    Production FormD T1 Classic (READ FIRST POST)

    My aquanaut arrived just in time for cyberpunk! It`s not 100% how I planned, simply because the tubes/fixings for them were too big to fit where I wanted to route them - so the fill/drain port is on the outlet from the pump. But very happy otherwise!
  4. T

    Production FormD T1 Classic (READ FIRST POST)

    Doesn't help if I need to clear CMOS because the system's not posting! ;)
  5. T

    Production FormD T1 Classic (READ FIRST POST)

    Sorry if this has been covered. What's the consensus on PCIE 4.0 capable risers? I know the 3m one is supposed to have the bandwidth, but does it actually handshake as pcie 4.0? I'd really rather not have to take the 3090 out and replace it with my old PCIE 3.0 card every time I clear CMOS.... 😢
  6. T

    Production FormD T1 Classic (READ FIRST POST)

    I have an FE in mine and the Temps that I can read are very good - similar to @SushiRoll. I don't think there are temp sensors on the vram - if they are, they aren't showing anywhere in GPUZ. The m.2 SSD I have on the back slot of my mobo is still cooler than the one on the front.
  7. T

    Production FormD T1 Classic (READ FIRST POST)

    Well that was stressfull. 2-slot to 3 slot without dismantling the loop. 🥵
  8. T

    Production FormD T1 Classic (READ FIRST POST)

    Ahh, I see, didn't notice it was in 3 slot config...
  9. T

    Production FormD T1 Classic (READ FIRST POST)

    How is the stability of the card without the PCIE bracket?
  10. T

    Production FormD T1 Classic (READ FIRST POST)

    Just managed to nab a 3090 FE after missing out on a 3080 FE that I had in my basket! Now to figure out how I'm going to fit it in.... I tried searching the thread but couldn't see anything.
  11. T

    Production FormD T1 Classic (READ FIRST POST)

    Do you even want your SSD to be that cool?
  12. T

    Production FormD T1 Classic (READ FIRST POST)

    https://j-hackcompany.com/?product=j-hack-m2426-customizable-kit
  13. T

    Production FormD T1 Classic (READ FIRST POST)

    In two slot mode - yes?
  14. T

    Production FormD T1 Classic (READ FIRST POST)

    Most of the heat in that case is just being blown directly down - so it just rises straight back into the case! I mean, it doesn’t ever actually leave the case itself, just goes into the bottom compartment. And unless you leave the case open or have the fan ducted to the side panel, the gpu is...
  15. T

    Production FormD T1 Classic (READ FIRST POST)

    100% This is the only time I have come anywhere close to buying a card at launch - and the only reason I am doing so is because what may turn out to be my favourite game of all time is being released (CB2077) and I want to play it at absolutely the best fidelity I can. Unless you are somewhat...