Recent content by Gucky

The panel can bend a bit, I already have a 1660 in there that is a big over 40mm. As long as the fans don't protude and get stuck it is alright. (already had that happen with another card) In worst case, I have to use longer screws with a washer... I know that. :D Sadly the Zotac 4070 Super is...

Hello. Soon the "old" 4070's will be lowered in price and I want to buy one for my Densium 4+ V1. I don't want to buy a 4070 Super unless it has no 12VHPWR connector. Not because it is unsafe or anything, but my FLEX-ATX PSU is not modular and I don't want to fit a adapter in there. The other...

Sadly I need a 220mm (at most) card and shaving off (literally) 1,5cm doesn't seem viable. And the 12VHPWR adapter doesn't fit in a small chassis with a non-modular FLEX-ATX PSU.

I'd recommend the same. As for the 600 Watts. Honestly you will never be able to use more then 400 Watts without running into thermal Issues first, since the maximum GPU-Size you can fit currently is a 220Watt RTX 3070, if you make a specific cooler mod. As for the CPU...try running a >150 Watts...

My GPU i have installed is NOT flush with the back, there is a 1-2 mm gap. It comes down to the PCI-E Riser position. And the 222.1mm of the Zotac is measured without the slotbracket, i think. The Fan-Shroud is plastic. And according to Zotac the backplate is made from metal..maybe trying to...

I have some Patriot Viper Steel (about 44,4mm) in the D4+ V1. They do press against the sidepanel, even if it is just a little bit...The sidepanel still closes, but also rests against the RAM. Sooo I'd say 44mm MIGHT fit, but is also a bit too high. I use the Gigabyte B550I Aorus Pro AX Board...

@AMv8-1day Well I looked a bit on techpowerup and found this: https://www.techpowerup.com/gpu-specs/asus-dual-rtx-3070-si.b9530 A 3070 with really short PCB, but big cooler...229mm long...9mm too much for the D4+. Those 9mm are shroud and maybe a few fins only. And this try on reddit...

I know that the EVGA XC Gaming and the Asus Dual Mini 3060Tis fit. (I have the latter) A Zotac Twin Edge might be just a few mm too long. You could literally shave it down, since its only the Backplate and Fanshroud. If the Size of the V2 is the same as my V1 D4+ Cards from other AIBs including...

It depends if you want the Densium 4 or 4+. I took the 4+ since its easier to find GPUs and it has easy room for a Sata SSD and cables. And who knows what size future cards will be... My build is a 3700X and a 3060TI which are sub 300W togather. (I looked for a B550 ITX board on ebay germany and...

Just want to add something, when building a PC with a Riser, since i made that stupid mistake. If you use a PCI-E 3.0 Riser, but a PCI-E 4.0 Board and GPU, you won't get a video output. You need to manually change the PCI-E Gen in the Bios to 3.0 beforehand, by slotting the GPU into the Board...

Just preordered the D4 plus V2. Have to sell my D4plus V1 locally, when i get it XD. Oh btw you forgot to put in the size of your Leather Desk Mat in the Shop.

I have the Asus Dual Mini 3060Ti (bought it used for 400€), which is has the same dimensions (same cooler) as the Asus 3060 you posted. It fits good in the D4+ V1. The EVGA XC Gaming should fit as well. Actually those 2 Cards are the only 3060Ti that fit the D4+...There is the MSI Aero ITX, but...

Ryzen is a bit...complicated and dumb. Fist of all the standard PPT is TDPx1,35. For the 5600 that would be around 88W. And the Temp Limit is usually 100°C. The Problem with PPT is that Ryzen uses a high Singlecore Boost that makes the CPU very hot. For my 5950X it is 5,05Ghz@1.5V. That high...

Asus TUF 1660Super, was able to get one used for cheap. The fan shroud was 1-1,5mm too thick, but by removing the thick plastic backplate, i was able to bend the GPU inwards a little bit. Yes the sidepanel is touching the GPU fan shroud, but it doesn't block the Fans. As for the Mainboard. The...

So i recieved my PSU today, the Case (D4+V1) came Monday this week. The Case has a few imperfections from the powder coating, but nothing major and a side panel was bent from the shipping. But i was able to straighten it. In order to fit my Parts in, i had to remove the backplate from my...